A loading bay door automation package is an electric operator, control panel and set of safety devices fitted to an existing manual sectional door or roller shutter so it opens and closes at the press of a button. Once motorised, the door is a power-operated door, so it needs protection against trapping, such as a safety edge and photocells, and a way to be opened by hand if the power fails.
Where does this fit at a dock in Hampshire?
Preparing a site in Hampshire for a health and safety review is a good moment to motorise doors with proper trapping protection rather than leave staff on hand chains. Upgrading manual docks to electric operation is a practical first step for sites in Hampshire that later plan to add interlocks and traffic lights.
Heavy shutters on trade and merchant sites in Hampshire can be tiring to open by hand, which is where an external chain-drive motor earns its place.
Your loading bay stays our responsibility from the survey to the handover. In Hampshire, the survey and written quote are free, and the quoted price is fixed for the agreed scope. Installation is carried out by specialist engineers working under our management, at times planned with you to protect your loading schedule. Out-of-hours work is available by arrangement. We finish by testing the equipment and handing over its documentation.
What is involved in fitting a motor to an existing dock door?
Fitting a motor to an existing dock door usually takes a few hours to a day per door, and starts with checking that the door itself is safe to automate.
- The door is checked for balance, spring condition, cable wear and track alignment.
- The operator is mounted on the shaft, ceiling rail or barrel bracket.
- The control panel is fixed in a safe position with a clear view of the door.
- A safety edge is fitted to the bottom rail and photocells are set across the opening.
- Limits, forces and controls are set, then the door is tested against the relevant safety checks.
You will need to provide a suitable isolated power supply near the door, or ask us to include it, and keep the door out of use during the work. Single-phase supplies suit many operators, but larger industrial operators may need three-phase power, which we confirm at survey.
Is my existing door suitable for automation?
An existing door is usually suitable for automation if it is structurally sound, correctly balanced and runs smoothly by hand. A motor should never be used to make up for a door that is heavy, stiff or damaged.
Signs a door can be automated:
- It lifts evenly by hand and stays put when released halfway.
- Springs, cables, rollers and tracks are in good order.
- Panels or laths are not badly dented or distorted.
Signs it may be better replaced:
- Springs are near the end of their life or have broken before.
- The door is single skin and the building is now heated.
- Parts are no longer available for the door model.
Where replacement makes more sense, we will say so and can quote for sectional loading bay doors supplied with an operator already fitted, so you can compare the two routes on cost.
Towns we cover in Hampshire
We cover loading bay door automation throughout Hampshire, and the towns below each have their own page. If yours is not listed, get in touch anyway.
- Southampton
- Portsmouth
- Basingstoke
- Gosport
- Waterlooville
- Farnborough
- Eastleigh
- Winchester
- Havant
- Andover
- Fareham
- Aldershot
- Fleet
- Totton
- New Milton
- Bordon
- Hythe
- Yateley
- Alton
- Emsworth
- Hedge End
- Bishopstoke
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
What do the rules in England mean for the work?
Sites in Hampshire fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.
Questions
Can you work outside our normal operating hours in Hampshire?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Is VAT included in your guide prices for loading bay door automation?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Hampshire as everywhere else: for loading bay door automation, it is £1,100 to £2,400 per door, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
What is the difference between hold-to-run and impulse control?
With hold-to-run the operator must keep pressing the button for the door to move, so they watch it throughout. With impulse control a single press opens or closes the door fully, which saves time but requires full safety sensing such as a safety edge and photocells, because no one may be watching.
How long does it take to automate a dock door?
Most automations are completed within a working day per door, once any repairs to the door itself have been done. Larger shutters, or doors that need a new power supply, can take longer. We plan the work so that only the door being automated is out of use.
Other services in Hampshire
Full guide to loading bay door automation · All loading bay services in Hampshire