- Location
- Fareham, Hampshire
- Main postcode district
- PO16
- Nearby (straight line)
- Gosport (4 miles), Portsmouth (5 miles) and Hedge End (7 miles)
- Survey and quote
- Free, with a fixed written quote
A loading bay door automation package is an electric operator, control panel and set of safety devices fitted to an existing manual sectional door or roller shutter so it opens and closes at the press of a button. Once motorised, the door is a power-operated door, so it needs protection against trapping, such as a safety edge and photocells, and a way to be opened by hand if the power fails.
What matters for loading bay door automation in Fareham?
Landlords upgrading manual doors across a multi-let estate in Fareham can standardise operators and controls so every tenant gets the same reliable setup. Heavy shutters on trade and merchant sites in Fareham can be tiring to open by hand, which is where an external chain-drive motor earns its place.
Operations in Fareham with manual sectional doors in good condition can often add an electric operator for much less than the cost of a new door.
Here is what happens after you contact us about a site in Fareham. We arrange a free survey, measure up and send a fixed written quote. If you go ahead, we manage the whole job, including ordering, delivery and coordination with your site team. Specialist installation engineers working under our management do the fitting, at times built around your loading schedule, with out-of-hours work by arrangement. Testing and handover documents close the job.
What is involved in fitting a motor to an existing dock door?
Fitting a motor to an existing dock door usually takes a few hours to a day per door, and starts with checking that the door itself is safe to automate.
- The door is checked for balance, spring condition, cable wear and track alignment.
- The operator is mounted on the shaft, ceiling rail or barrel bracket.
- The control panel is fixed in a safe position with a clear view of the door.
- A safety edge is fitted to the bottom rail and photocells are set across the opening.
- Limits, forces and controls are set, then the door is tested against the relevant safety checks.
You will need to provide a suitable isolated power supply near the door, or ask us to include it, and keep the door out of use during the work. Single-phase supplies suit many operators, but larger industrial operators may need three-phase power, which we confirm at survey.
What safety rules apply once a manual door is motorised?
Once a manual door is fitted with a motor it becomes a power-operated door, and the rules for powered doors apply in full. Automation is more than bolting on a motor.
- Workplace law: regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Workplace (Health, Safety and Welfare) Regulations (Northern Ireland) 1993, require powered doors to have suitable and effective features to prevent trapping, and to be operable by hand where necessary unless they open automatically on power failure.
- Safety in use: BS EN 12453 sets out safety requirements and test methods for power-operated doors, including how closing forces are limited and measured.
- Product standard: BS EN 13241 covers the door as a product.
- Marking: in Great Britain a powered door may carry the UKCA or the CE mark; in Northern Ireland the CE mark, or CE with UKNI, applies.
Enforcement sits with HSE in Great Britain and HSENI in Northern Ireland. The results of the safety checks carried out at commissioning form part of the handover.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Condition of any existing leveller pit, kerb angles and pit drainage
- Scope to convert ground-level doors into docks or add lift tables
- Dock height and the mix of trailers you load
- Traffic routes for vehicles and separation of pedestrians
- Control positions, isolators and any existing interlocks
- Headroom above the opening and which track type will suit it
Options to discuss
Dock interlocks
Wiring that links the door to levellers, shelters, restraints or traffic lights so the dock can only run in a safe sequence.
Remote and drive-through controls
Radio remotes, pull cords and induction loops let drivers and forklift operators open the door without stopping, alongside the main push-button panel.
Regulations and approvals in England
In England, Approved Document L (2021) sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. That shapes door specification for sites in Fareham, so we confirm the requirement for your project and check what applies at survey before recommending a door.
Questions about loading bay door automation in Fareham
How long does installation take at a site in Fareham?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Will you deal with building control and planning for a project in Fareham?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
Is VAT included in your guide prices for loading bay door automation?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Hampshire as everywhere else: for loading bay door automation, it is £1,100 to £2,400 per door, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Can drivers open the door without leaving the forklift?
Yes, pull cords, radio remotes and induction loops in the floor can all open a powered door without the driver getting down. The right choice depends on traffic, and any opening method that does not need a button held must be paired with safety devices so the door cannot close on a vehicle or person.
Do we need a three-phase supply?
Not always. Many operators for small and medium doors run on a single-phase supply, while larger industrial operators for heavy dock doors often need three-phase power. We confirm the supply your door needs at survey and can include any electrical work in the written quote.
Loading bay door automation near Fareham
Nearby places we cover, measured from Fareham, include Gosport (4 miles), Portsmouth (5 miles) and Hedge End (7 miles). Ask if your own town is missing.
Other loading bay services in Fareham
Full guide to loading bay door automation · Everything we do in Fareham
Speak to us about your Fareham loading bay. We will ask the right questions, then set out the next step clearly.