A sectional loading bay door is an overhead door made from horizontal insulated steel panels hinged together, which run up on rollers in side tracks and park beneath the ceiling or up the wall when open. Panels are commonly 40 to 80 mm thick, so the door seals and insulates better than a single-skin shutter, and it can be operated by hand chain, push-up or electric motor.
Where does this fit at a dock in Hampshire?
Our survey for a site in Hampshire follows the same approach as anywhere else: measure the opening, check headroom and services, then quote a fixed price. Food and drink businesses in Hampshire running temperature-controlled goods-in areas can choose thicker panels to hold conditions steady between deliveries.
If you are fitting out a new warehouse in Hampshire, specifying insulated sectional doors from the start avoids disruptive changes once the building is occupied.
Your loading bay stays our responsibility from the survey to the handover. In Hampshire, the survey and written quote are free, and the quoted price is fixed for the agreed scope. Installation is carried out by specialist engineers working under our management, at times planned with you to protect your loading schedule. Out-of-hours work is available by arrangement. We finish by testing the equipment and handing over its documentation.
Should a sectional dock door have vision panels or a wicket door?
Vision panels are worth adding on most dock doors, while wicket doors are rarely used on loading bays. A row of double-glazed windows lets staff see whether a trailer is on the bay and brings daylight into the dock area.
- Vision panels can be a single row at eye level or fully glazed sections in aluminium frames.
- Glazed sections lower the door's insulation, so on a heated or chilled building we balance daylight against thermal performance.
- Wicket doors are uncommon on docks because there is a trailer or a drop to the yard behind the door, so they rarely offer a safe exit. A separate pedestrian door beside the bay is usually the better answer.
It is also worth deciding now whether the door will be interlocked with the leveller, so the lip cannot be raised until the door is fully open. Adding links like this later is harder.
Do sectional loading bay doors have to meet energy and safety rules?
Yes. New and replacement sectional loading bay doors fall under building energy rules and workplace safety law, and the detail differs between the four nations.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. Wales, Scotland and Northern Ireland each have their own energy rules, and we confirm the figure that applies to your nation and project.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Workplace (Health, Safety and Welfare) Regulations (Northern Ireland) 1993, require upward-opening doors to have a device that stops them falling back. On a sectional door that usually means spring break and cable break protection.
- Product standard: BS EN 13241 is the product standard for industrial doors, and powered doors are also assessed against BS EN 12453 for safety in use.
- Marking: a powered door in Great Britain may be UKCA or CE marked, while in Northern Ireland it is the CE mark, or CE with UKNI, that applies.
Towns we cover in Hampshire
Find your town in the list below for details of sectional loading bay doors across Hampshire, or contact us if your location is not shown.
- Southampton
- Portsmouth
- Basingstoke
- Gosport
- Waterlooville
- Farnborough
- Eastleigh
- Winchester
- Havant
- Andover
- Fareham
- Aldershot
- Fleet
- Totton
- New Milton
- Bordon
- Hythe
- Yateley
- Alton
- Emsworth
- Hedge End
- Bishopstoke
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
Regulations and approvals in England
Sites in Hampshire fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.
Questions
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Hampshire site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Hampshire, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Can a manual sectional door be motorised later?
Often yes, if the door is sound and correctly balanced. An operator is fitted to the spring shaft or a trolley drive is fixed to the ceiling, and the door gets a safety edge and photocells at the same time. We check spring condition and balance first, because a motor should never be used to make up for a badly balanced door.
What panel thickness should we choose for a heated warehouse?
For most heated warehouses a panel at the thicker end of the common 40 to 80 mm range is the sensible starting point, because it insulates better. Thinner panels can suit unheated stores. New and replacement doors also need to meet the energy rules for your nation, which we check when specifying.
Other services in Hampshire
Full guide to sectional loading bay doors · All loading bay services in Hampshire