- Location
- Havant, Hampshire
- Main postcode district
- PO9
- Nearby (straight line)
- Emsworth (2 miles), Waterlooville (3 miles) and Portsmouth (6 miles)
- Survey and quote
- Free, with a fixed written quote
A loading bay door automation package is an electric operator, control panel and set of safety devices fitted to an existing manual sectional door or roller shutter so it opens and closes at the press of a button. Once motorised, the door is a power-operated door, so it needs protection against trapping, such as a safety edge and photocells, and a way to be opened by hand if the power fails.
Is this right for your site in Havant?
Landlords upgrading manual doors across a multi-let estate in Havant can standardise operators and controls so every tenant gets the same reliable setup. On older units in Havant where the original doors are still sound, automation keeps the existing door working while removing the effort of hand chains.
Heavy shutters on trade and merchant sites in Havant can be tiring to open by hand, which is where an external chain-drive motor earns its place.
How does an installation in Havant work? First, a free, no-obligation survey to measure up and understand the operation. Next, a fixed written quote. Then a programme agreed with you, so the work fits around deliveries, with out-of-hours slots if needed. The installation itself is carried out by specialist engineers who answer to us, and it finishes with testing, a walk-through for your staff and a handover pack.
How can door controls and interlocks make the dock safer?
Interlocks link the door to the rest of the dock so that each piece of equipment can only move when it is safe, which reduces both accidents and damage.
- Leveller interlock: the leveller cannot be raised until the door is fully open, protecting the door from the lip.
- Restraint or traffic light interlock: the door only opens once the trailer is restrained or the outside light shows red to the driver.
- Shelter interlock: with inflatable shelters, the door opens only once the cushions have inflated.
- Control mode: hold-to-run keeps the operator watching the door, while impulse controls save time but need full safety sensing.
Interlocks are far simpler to add while a door is being automated than as a separate job later. See dock traffic lights and interlocks for how a full dock sequence is set up.
How much does it cost to motorise a loading bay door?
Automating an existing loading bay door typically costs £1,100 to £2,400 per door, excluding VAT, supply and fit. That covers the operator, control panel, safety devices, wiring at the door and commissioning.
What moves the price:
- Door type and weight: heavy shutters and large sectional doors need more powerful operators.
- Operator type: shaft-mounted, trolley, tubular or external chain-drive.
- Control mode: hold-to-run controls need fewer safety devices than impulse or automatic operation.
- Safety devices: safety edge, photocells and, for automatic closing, additional sensing.
- Extras: remote controls, pull cords, induction loops and interlocks with levellers or traffic lights.
- Power: whether a suitable isolated supply already exists near the door.
If the door needs work before it can be motorised, such as new springs or rollers, we price that separately so you can see each cost. The written quote after a free site survey is the fixed price.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Control positions, isolators and any existing interlocks
- How drivers are prevented from pulling away too early
- Condition of any existing leveller pit, kerb angles and pit drainage
- Forklift and pallet truck loads crossing the leveller platform
- Scope to convert ground-level doors into docks or add lift tables
- Wind exposure at the dock, which affects door and shelter choice
Options to discuss
Tubular or external shutter motor
A motor inside the barrel for small and medium shutters, or a side-mounted chain-drive unit for large, heavy shutters at busy openings.
Remote and drive-through controls
Radio remotes, pull cords and induction loops let drivers and forklift operators open the door without stopping, alongside the main push-button panel.
Regulations and approvals in England
In England, Approved Document L (2021) sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. That shapes door specification for sites in Havant, so we confirm the requirement for your project and check what applies at survey before recommending a door.
Questions about loading bay door automation in Havant
Do you cover Havant for loading bay door automation?
Yes. We take on loading bay door automation for businesses in Havant and across Hampshire. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
Can you work outside our normal operating hours in Havant?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Havant, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Can any manual door be motorised?
No, only doors that are sound, balanced and run smoothly by hand should be motorised. Doors with weak springs, damaged panels, bent laths or obsolete parts may need repair first, or may be better replaced. We check this at survey and tell you which applies before quoting.
Do we need a three-phase supply?
Not always. Many operators for small and medium doors run on a single-phase supply, while larger industrial operators for heavy dock doors often need three-phase power. We confirm the supply your door needs at survey and can include any electrical work in the written quote.
Loading bay door automation near Havant
If your site is not in Havant itself, it may be near one of these: Emsworth (2 miles), Waterlooville (3 miles) and Portsmouth (6 miles). Pick the closest.
Other loading bay services in Havant
Full guide to loading bay door automation · Everything we do in Havant
Speak to us about your Havant loading bay. We will ask the right questions, then set out the next step clearly.