- Location
- Fareham, Hampshire
- Main postcode district
- PO16
- Nearby (straight line)
- Gosport (4 miles), Portsmouth (5 miles) and Hedge End (7 miles)
- Survey and quote
- Free, with a fixed written quote
A sectional loading bay door is an overhead door made from horizontal insulated steel panels hinged together, which run up on rollers in side tracks and park beneath the ceiling or up the wall when open. Panels are commonly 40 to 80 mm thick, so the door seals and insulates better than a single-skin shutter, and it can be operated by hand chain, push-up or electric motor.
What should sites in Fareham consider?
For distribution sites in Fareham with heavy daily trailer traffic, an electric sectional door with photocells keeps the bay moving without staff hauling on a chain. A dock facing the prevailing wind, wherever it sits in Fareham, benefits from a well-sealed sectional door that stops rain and draughts reaching the loading area.
Landlords preparing an industrial unit in Fareham for a new tenant may choose to replace tired dock doors so the building is ready to trade from day one.
If you are planning sectional loading bay doors for a site in Fareham, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
Do sectional loading bay doors have to meet energy and safety rules?
Yes. New and replacement sectional loading bay doors fall under building energy rules and workplace safety law, and the detail differs between the four nations.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. Wales, Scotland and Northern Ireland each have their own energy rules, and we confirm the figure that applies to your nation and project.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Workplace (Health, Safety and Welfare) Regulations (Northern Ireland) 1993, require upward-opening doors to have a device that stops them falling back. On a sectional door that usually means spring break and cable break protection.
- Product standard: BS EN 13241 is the product standard for industrial doors, and powered doors are also assessed against BS EN 12453 for safety in use.
- Marking: a powered door in Great Britain may be UKCA or CE marked, while in Northern Ireland it is the CE mark, or CE with UKNI, that applies.
What happens on site when a sectional dock door is installed?
Fitting a sectional dock door often takes around a day per opening once the door is on site, though very large doors or awkward fixings take longer. The bay is out of use while the work is under way.
A typical installation runs like this:
- The old door, if there is one, is taken down and removed from site.
- Steel angles or packers are fixed to the opening so the tracks run true.
- Tracks, springs and panels are assembled and the door is balanced.
- The operator, safety edge, photocells and controls are fitted and wired.
- The door is tested, adjusted and handed over.
Before we arrive you will need a clear area inside the opening for access equipment and the bay taken out of service. Electric doors also need a suitable isolated power supply near the door head, single or three-phase depending on the operator, which we confirm in the quote. On multi-door sites we work bay by bay so the rest of the dock keeps running.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Yard gradient and the slope of the approach to the dock
- Wind exposure at the dock, which affects door and shelter choice
- Working hours, shift patterns and windows for out-of-hours work
- Headroom above the opening and which track type will suit it
- Clear opening width and height for each door
- Age and condition of the equipment already in place
Options to discuss
Vision panels
Double-glazed windows or fully glazed aluminium sections let drivers and dock staff see the bay and bring in daylight, at some cost to insulation.
Thicker insulated panels
Panels at the upper end of the common 40 to 80 mm range improve insulation for heated warehouses and temperature-controlled goods-in areas.
Which rules apply in England?
Workplace safety in England is regulated by HSE. For a loading bay in Fareham, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about sectional loading bay doors in Fareham
How do you price sectional loading bay doors for a site in Fareham?
Guide budgets for supply and fit are £2,400 to £5,200 per door, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Fareham, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
How long does installation take at a site in Fareham?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
What panel thickness should we choose for a heated warehouse?
For most heated warehouses a panel at the thicker end of the common 40 to 80 mm range is the sensible starting point, because it insulates better. Thinner panels can suit unheated stores. New and replacement doors also need to meet the energy rules for your nation, which we check when specifying.
Can the door be supplied in our company colours?
Yes, panels come in a range of standard colours, and many manufacturers can supply other shades at extra cost and with a longer lead time. The inside face is usually white or light grey. We confirm the colour, finish and lead time in the written quote.
Sectional loading bay doors near Fareham
Nearby places we cover, measured from Fareham, include Gosport (4 miles), Portsmouth (5 miles) and Hedge End (7 miles). Ask if your own town is missing.
Other loading bay services in Fareham
Full guide to sectional loading bay doors · Everything we do in Fareham
Request a quote for your loading bay in Fareham, attaching photos of the dock, the equipment and any damage.