Sectional loading bay doors in Eastleigh

Location: Eastleigh, Hampshire
Main postcode district: SO50
Nearby (straight line): Bishopstoke (1 mile), Hedge End (4 miles) and Southampton (5 miles)
Survey and quote: Free, with a fixed written quote

Sectional loading bay doors, in short

A sectional loading bay door is an overhead door made from horizontal insulated steel panels hinged together, which run up on rollers in side tracks and park beneath the ceiling or up the wall when open. Panels are commonly 40 to 80 mm thick, so the door seals and insulates better than a single-skin shutter, and it can be operated by hand chain, push-up or electric motor.

How does this suit sites in Eastleigh?

For distribution sites in Eastleigh with heavy daily trailer traffic, an electric sectional door with photocells keeps the bay moving without staff hauling on a chain. If you are fitting out a new warehouse in Eastleigh, specifying insulated sectional doors from the start avoids disruptive changes once the building is occupied.

Ageing units around Eastleigh sometimes have low lintels or pipework above the opening, which a low-headroom or high-lift track can be chosen to work around.

Any project involving sectional loading bay doors at a working site in Eastleigh takes planning. We survey free of charge, quote a fixed price in writing, and then agree a programme that keeps as much of the dock running as possible. Specialist installation engineers carry out the work under our management, out of hours if that suits you better. On completion we test each item, show your team how it operates and leave the documentation with you.

Do sectional loading bay doors have to meet energy and safety rules?

Yes. New and replacement sectional loading bay doors fall under building energy rules and workplace safety law, and the detail differs between the four nations.

Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. Wales, Scotland and Northern Ireland each have their own energy rules, and we confirm the figure that applies to your nation and project.
Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Workplace (Health, Safety and Welfare) Regulations (Northern Ireland) 1993, require upward-opening doors to have a device that stops them falling back. On a sectional door that usually means spring break and cable break protection.
Product standard: BS EN 13241 is the product standard for industrial doors, and powered doors are also assessed against BS EN 12453 for safety in use.
Marking: a powered door in Great Britain may be UKCA or CE marked, while in Northern Ireland it is the CE mark, or CE with UKNI, that applies.

How much does a sectional loading bay door cost?

A sectional loading bay door typically costs £2,400 to £5,200 per door, excluding VAT, supply and fit, for a made-to-measure insulated door fitted and working.

Where your door lands in the range depends on:

Opening size: larger doors need more panel area, heavier springs and longer track.
Panel thickness and finish: thicker insulated panels and non-standard colours add cost.
Track type: high-lift and vertical lift tracks use more steel and fixings than standard lift.
Operation: an electric operator with safety edge and photocells costs more than chain or push-up operation.
Vision panels and extras: glazed sections, interlocks to the leveller and links to traffic lights.
Site conditions: removing an old door, making good the opening, getting power to the door head and out-of-hours working.

We price after a free site survey, and the written quote is the fixed price for the work described. You can compare typical figures on our price guide.

Guide price, Eastleigh

£2,400–£5,200 per door, ex VAT

The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.

Survey checklist for your dock

Control positions, isolators and any existing interlocks
Clear opening width and height for each door
Access for deliveries, cranes or lifting equipment during installation
Condition of any existing leveller pit, kerb angles and pit drainage
Dock height and the mix of trailers you load
Whether planning, building control or a building warrant may be needed

Options to discuss

Electric operator

A shaft-mounted or trolley operator with push-button controls, safety edge and photocells. Suits busy bays and can be interlocked with levellers, shelters and traffic lights.

Thicker insulated panels

Panels at the upper end of the common 40 to 80 mm range improve insulation for heated warehouses and temperature-controlled goods-in areas.

Which rules apply in England?

Sites in Eastleigh fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.

Questions about sectional loading bay doors in Eastleigh

What details do you need from us to quote for sectional loading bay doors?

To get started, send the site address in Eastleigh, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.

Is the site survey in Eastleigh free?

Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.

Will you deal with building control and planning for a project in Eastleigh?

We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.

Will the bay be out of action for long?

Usually only on installation day. The door is made to order before we book the fitting, so the old door stays in use until the new one is ready to go in. On sites with several bays we fit one opening at a time, keeping the rest of the dock running.

What panel thickness should we choose for a heated warehouse?

For most heated warehouses a panel at the thicker end of the common 40 to 80 mm range is the sensible starting point, because it insulates better. Thinner panels can suit unheated stores. New and replacement doors also need to meet the energy rules for your nation, which we check when specifying.

Sectional loading bay doors near Eastleigh

Distances are measured from Eastleigh. Nearby towns we cover include Bishopstoke (1 mile), Hedge End (4 miles) and Southampton (5 miles), and other towns in the area are covered too.

Other loading bay services in Eastleigh

Full guide to sectional loading bay doors · Everything we do in Eastleigh

Use the quote tool to tell us about the doors, levellers or shelters at your Eastleigh site, and we will be in touch to arrange the next step.