- Location
- Reigate, Surrey
- Main postcode district
- RH2
- Nearby (straight line)
- Redhill (2 miles), Horley (5 miles) and Dorking (6 miles)
- Survey and quote
- Free, with a fixed written quote
A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
What should sites in Reigate consider?
Before recommending a lip extension for a dock in Reigate, we record the trailers that actually arrive, including tail lifts and rear overhangs. Replacing worn swing-lip levellers at a site in Reigate is a good moment to ask whether the current trailer mix now calls for telescopic lips.
Cold chain operators around Reigate loading refrigerated trailers right to the doors may find a telescopic lip makes the last pallets far easier to handle.
Here is what happens after you contact us about a site in Reigate. We arrange a free survey, measure up and send a fixed written quote. If you go ahead, we manage the whole job, including ordering, delivery and coordination with your site team. Specialist installation engineers working under our management do the fitting, at times built around your loading schedule, with out-of-hours work by arrangement. Testing and handover documents close the job.
How are drive-away risks managed while the lip rests on a trailer?
Drive-away risks are managed by stopping the vehicle leaving until loading has finished and the lip has been withdrawn, using traffic lights, vehicle or trailer restraints, or the person in charge keeping the keys or paperwork. HSE workplace transport guidance (HSG136) and the HSE loading factsheet (followed by HSENI in Northern Ireland) call for safeguards against drivers driving away too early.
- Why it matters: a lip resting on the bed is only safe while the trailer stays put, and trailer creep during forklift loading can open a gap at the dock edge.
- Equipment duties: the leveller is work equipment under PUWER 1998 in Great Britain or PUWER (Northern Ireland) 1999, so it must be maintained and inspected where deterioration could lead to danger. Engineering insurers commonly inspect at 12-month intervals.
- Standard: BS EN 1398:2009 sets the safety requirements for dock levellers and is current, under review.
Enforcement is by HSE in Great Britain and HSENI in Northern Ireland. Our guide to preventing drive-away and trailer creep compares the safeguards.
How far should a telescopic lip extend?
A telescopic lip should extend far enough to reach clear bed space on every trailer you load, including over tail lifts, while still leaving a secure overlap on the bed. Telescopic lips commonly extend 500 to 1,000 mm.
- Around 500 mm: suits fleets without tail lifts that need precise placement and end loading.
- Up to around 1,000 mm: reaches over folded tail lifts and across the larger gap left where deep bumpers hold trailers back from the dock edge.
- Platform length: should match the lip, as a long reach on a short platform can leave steep gradients.
- Lip width: full-width lips suit most work, while narrower or tapered lips help with smaller vehicles.
We record the rear details of the trailers you receive, including tail lift depth and bumper projection, then recommend the shortest extension that covers them all. A longer lip than you need adds cost and weight without benefit.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Gaps around trailers where heated or chilled air escapes
- Power supply at each bay, including three-phase availability
- Scope to convert ground-level doors into docks or add lift tables
- Escape routes and pedestrian doors close to the bay
- Drainage on recessed or sloping dock approaches
- Forklift and pallet truck loads crossing the leveller platform
Options to discuss
1,000 mm lip extension
A longer reach that clears folded tail lifts and deep bumper projections, so rigids and tail-lift trailers can be loaded at the same bay.
Insulated cold store version
An insulated platform with perimeter seals for chilled and frozen docks, often paired with an inflatable shelter and an insulated dock door.
Planning, building control and safety law in England
Workplace safety in England is regulated by HSE. For a loading bay in Reigate, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about telescopic-lip dock levellers in Reigate
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Reigate, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Which building and safety rules apply to a site in Reigate?
It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Reigate, we check what applies at survey and design to it.
How do you price telescopic-lip dock levellers for a site in Reigate?
Guide budgets for supply and fit are £6,800 to £11,800 per leveller, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
What overlap should the lip have on the trailer bed?
The lip should rest on the trailer bed with the overlap the manufacturer specifies, so it cannot slip off as the trailer moves under load. Extending further than needed adds no benefit. We show dock staff what a correct overlap looks like at handover.
Can telescopic and swing-lip levellers be mixed on one dock?
Yes, and many sites do. Fitting telescopic levellers on the bays that receive tail-lift vehicles or need end loading, and swing-lip units on the rest, keeps costs down while covering every vehicle type. Clear bay signage helps drivers reverse onto the right one.
Telescopic-lip dock levellers near Reigate
We also cover towns near Reigate, including Redhill (2 miles), Horley (5 miles) and Dorking (6 miles). Each has its own page with the same services and process.
Other loading bay services in Reigate
Full guide to telescopic-lip dock levellers · Everything we do in Reigate
Have photos of the door, leveller or shelter? Send them with your enquiry and we can give a clearer answer for your Reigate site.