Dock shelter and seal repair covers restoring the weather seal around a docked trailer. Typical work includes replacing torn side and head curtains, worn foam seal pads and their covers, top pads and guide strips, repairing or replacing airbags and blowers on inflatable shelters, and straightening or replacing bent shelter frames, so the bay closes the gap between building and trailer again.
Is this right for your site in Moray?
Repairs to shelters and seals in Moray follow the same process as anywhere else in the UK, with the visit price agreed in writing first. Inflatable shelters at food sites in Moray depend on blowers and airbags working properly, and a slow-inflating shelter is worth checking before it fails.
Curtains tearing at the corners at docks in Moray can be a sign that taller or wider trailers are arriving than the shelter was sized for.
Repair and service visits in Moray are chargeable, and we agree the price with you in writing before anyone attends. Photos or a short video of the fault help us send the right engineer with the right parts. If the visit uncovers more work than expected, we quote it and wait for your approval before going ahead. After every visit you receive a written report on what was found and done.
How can I make shelter curtains and seal pads last longer?
Shelter curtains and seal pads last longest when trailers arrive straight, stop at the right distance and the parts are checked regularly. Most premature damage comes from how trailers are parked rather than from the material itself.
- Wheel guides: keep trailers centred so they do not drag one side curtain or crush one pad.
- Bumpers: worn bumpers let trailers reverse too far in and over-compress seals.
- Guide markings: clear centre lines on curtains and the dock help drivers line up.
- Early repairs: a small tear repaired early is cheaper than a full curtain later.
- Wear-resistant facings: seal pads can be specified with tougher covers where trailers rub most.
- Blower care: keeping blower intakes clear helps inflatable shelters inflate fully.
Our loading bay servicing includes shelters and seals, so wear is picked up alongside doors and levellers.
What happens on site during a shelter or seal repair?
During a shelter or seal repair the bay is closed to trailers while the engineer works from the yard, often using access equipment for the head curtain and top pad. Neighbouring bays can usually keep working, although access equipment may need space in front of them.
- Measure: where parts are made to measure, the shelter or seal is measured first and the parts ordered.
- Close the bay: no trailer on the dock and the yard area coned off.
- Isolate: on inflatable shelters, the blower supply is isolated and locked off.
- Replace parts: old curtains, pads or airbags are removed and new ones fitted, with frames straightened or replaced as agreed.
- Check the seal: overlap and compression are checked, with a trailer docked if one is available.
It helps if you can provide photos with a trailer docked, yard space for access equipment, a contact who can arrange electrical isolation and an agreed time when the bay can be released.
Towns we cover in Moray
We cover dock shelter and seal repairs throughout Moray, and the towns below each have their own page. If yours is not listed, get in touch anyway.
The visit price is agreed before anyone attends. All guide prices.
Which rules apply in Scotland?
Doors and dock equipment installed in Scotland may carry the UKCA or the CE mark, and we pass on the documentation for everything fitted in Moray. Because building warrant and planning questions can affect the programme, we check what applies before any work starts and raise any approvals early rather than assuming none are needed.
Questions
How often should equipment at our Moray site be serviced?
It depends on how hard the equipment works and on the manufacturer's recommendations. A multi-shift dock with frequent trailer movements needs more attention than a door that opens a few times a day. We suggest a schedule after looking at the equipment and how it is used, and we can line visits up with your insurance inspections where that helps.
What is the difference between servicing and a statutory inspection?
Servicing keeps equipment working: cleaning, adjusting, lubricating and replacing worn parts. A statutory inspection or thorough examination is a separate check by a competent person, often arranged through your engineering insurer. Dock levellers are commonly inspected under PUWER at 12-month intervals, and lift tables may need LOLER thorough examination, depending on the equipment and how it is used. Your insurer or competent person will confirm what applies.
How is the price for a shelter or seal repair agreed?
You describe the damage and send photos, and we agree the visit price in writing before anyone attends. For made-to-measure parts that may include a measuring visit. Any extra work found on site is quoted and only carried out once you approve it.
Can repairs help a chilled loading bay?
Yes. Gaps around a docked trailer let chilled air escape and warm, moist air in, which causes condensation and ice on the dock floor. Restoring the curtains, pads or airbags closes those gaps, helping keep the dock drier and safer to work in.
Other services in Moray
Full guide to dock shelter and seal repairs · All loading bay services in Moray