- Location
- Lerwick, Orkney, Shetland and the Western Isles
- Main postcode district
- ZE1
- Nearby (straight line)
- Remote location, covered by arrangement
- Survey and quote
- Free, with a fixed written quote
A dock seal is a set of fabric-covered foam pads fixed to the building around a loading bay door, usually a head pad and two side pads. When a trailer reverses in, its rear end presses into the foam, which compresses to close the gaps around the trailer body. Seals give a very tight fit but work best when the trailers using the bay are a consistent size.
Why do sites in Lerwick choose this?
Hygiene-sensitive sites in Lerwick, such as food processors, can use dock seals to reduce the gaps through which dust and pests might enter during loading. A dedicated chilled fleet serving a site in Lerwick can be sealed closely with foam pads, at lower cost than fitting an inflatable shelter.
Where trailers reverse onto a bay in Lerwick slightly off-centre, tapered side pads and wheel guides help protect the seal from rubbing.
The survey is free, the quote is written and the price is fixed: that is how every installation in Lerwick begins. We then manage the work from start to finish. Fitting is carried out by specialist installers under our management, phased so the operation keeps moving, and nights or weekends can be booked by arrangement. On the final day we test the equipment with you and hand over the operating and maintenance information.
What do workplace transport rules mean for a sealed dock?
A sealed dock still needs safeguards against a trailer leaving early, and the seal, bumpers and other dock equipment must be kept in safe working order. In Great Britain the regulator is HSE; in Northern Ireland it is HSENI.
- Drive-away: HSE workplace transport guidance (HSG136) and the HSE loading factsheet call for safeguards against drivers driving away too early, including traffic lights, vehicle or trailer restraints, or the person in charge keeping keys or paperwork until it is safe.
- Trailer creep: because the trailer is pressed into compressed foam, it can ease forward during forklift loading. Restraints and well-set bumpers help keep it in position.
- Equipment duties: a dock seal forms part of the loading bay's work equipment, so the general duty under PUWER 1998 in Great Britain, or PUWER (Northern Ireland) 1999, to keep equipment suitable and maintained applies.
Torn covers and crushed pads can hide damage to the fixings and wall behind, so seals belong in planned inspections of the dock.
When is a dock seal a better choice than a shelter?
A dock seal is a better choice than a shelter when the trailers using a bay are consistent in size, the dock height suits them, and the tightest practical seal matters. Mixed fleets are usually better served by a shelter.
- Consistent fleets: dedicated vehicles or regular hauliers using the same trailer type.
- Temperature control: chilled or heated buildings where gaps around the trailer are costly.
- Security and hygiene: fewer gaps for pests, dust and unauthorised access during loading.
- Budget: seals cost less than inflatable shelters for a close fit.
The trade-offs are that seals can leave gaps at trailer door hinges, side pads can intrude into the trailer opening if poorly sized, and the covers wear from rubbing. If your trailers vary, compare our retractable dock shelters before deciding, as they leave the full opening clear.
The same published guide range applies across Scotland; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Lighting inside trailers and at the dock face
- Gaps around trailers where heated or chilled air escapes
- Control positions, isolators and any existing interlocks
- Escape routes and pedestrian doors close to the bay
- Traffic routes for vehicles and separation of pedestrians
- How often each door cycles during a typical shift
Options to discuss
Replaceable wear pleats
Sacrificial fabric strips on the pad faces that take the rubbing from trailers and can be replaced without changing the whole cover.
Fixed head pad seal
A head pad and two side pads of set depth, the simplest and tightest arrangement where every trailer using the bay is the same height.
Regulations and approvals in Scotland
Energy standards for buildings in Scotland are set out in Section 6 of the Building Standards Technical Handbook. For new or replacement loading bay doors in Lerwick, we confirm the figure that applies to your project and check what applies at survey, rather than relying on rules written for elsewhere in the UK.
For Lerwick, installation work is planned in advance rather than on a routine round. The survey and quote are free; where we can, we group installation visits with other work nearby, and any travel and accommodation costs for fitting are set out clearly in the quote.
Questions about dock seals in Lerwick
Do you cover Lerwick for dock seals?
Yes. We take on dock seals for businesses in Lerwick and across Orkney, Shetland and the Western Isles. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Lerwick, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
How do you price dock seals for a site in Lerwick?
Guide budgets for supply and fit are £1,100 to £2,600 per set, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Can just the covers be replaced?
Yes, if the foam is still resilient and dry, new covers can often be fitted over the existing foam, which usually costs less than new pads. Waterlogged or permanently crushed foam should be replaced. Cover replacement is handled as a repair, with the visit price agreed beforehand.
Do trailer doors need to be opened before docking against a seal?
Yes, the rear doors are opened and folded back before the trailer reverses onto a seal, so the pads press against the rear of the trailer rather than the doors. Gaps can remain at the door hinges, which is a known limitation of seals compared with shelters.
Dock seals near Lerwick
Other loading bay services in Lerwick
Full guide to dock seals · Everything we do in Lerwick
Tell us what is happening at your Lerwick dock, what equipment is there and when it is used, and we will suggest the right next step.