Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
What should sites in Hampshire consider?
Any site in Hampshire considering these items gets the same survey and fixed written quote that we provide across England, Scotland, Wales and Northern Ireland. Warehouses in Hampshire loading deep trailers by forklift often find the back of the load hard to see without a dock light reaching into the trailer.
Tight yards in Hampshire where drivers reverse between parked trailers or around buildings make wheel guides especially useful for getting the trailer straight first time.
How does an installation in Hampshire work? First, a free, no-obligation survey to measure up and understand the operation. Next, a fixed written quote. Then a programme agreed with you, so the work fits around deliveries, with out-of-hours slots if needed. The installation itself is carried out by specialist engineers who answer to us, and it finishes with testing, a walk-through for your staff and a handover pack.
How much do dock lights and wheel guides cost?
Dock lights and wheel guides typically cost £280 to £950 per item, supplied and fitted, excluding VAT, where an item is one dock light or one wheel guide. A standard LED swing-arm light usually sits in the lower half of the range; long, heavy-section or cast-in guides sit towards the top.
What moves the price:
- Light specification: arm length, LED head output, protective guarding and whether a low-voltage supply is needed.
- Power: the distance to a suitable supply and how the cable is contained.
- Guide length and section: longer guides and heavier steel cost more.
- Yard surface: sound concrete takes anchors directly; tarmac usually needs a concrete base first, priced after survey.
- Number of bays: fitting several bays in one visit lowers the cost per item.
These are guide budgets. After a free site survey we send a written quote, which is the fixed price. VAT is added at the standard rate.
Do health and safety rules cover dock lights and wheel guides?
Dock lights and wheel guides support your wider loading bay safety duties rather than replacing them. Once fitted, a dock light is work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so it must be suitable, maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
HSE's guide to workplace transport safety (HSG136) is the main reference for managing vehicles in the yard, and its loading guidance says there should be safeguards against drivers driving away too early, such as traffic lights, restraints or key control. Wheel guides and dock lights do not meet that requirement on their own, but they help drivers park accurately and help dock staff see what they are doing.
Electrical work for dock lights is carried out by qualified electricians and tested before use. The regulator is HSE in Great Britain and HSENI in Northern Ireland.
Towns we cover in Hampshire
Choose a town below to see how we handle dock lights and wheel guides in that part of Hampshire.
- Southampton
- Portsmouth
- Basingstoke
- Gosport
- Waterlooville
- Farnborough
- Eastleigh
- Winchester
- Havant
- Andover
- Fareham
- Aldershot
- Fleet
- Totton
- New Milton
- Bordon
- Hythe
- Yateley
- Alton
- Emsworth
- Hedge End
- Bishopstoke
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
What do the rules in England mean for the work?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Hampshire. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions
What details do you need from us to quote for dock lights and wheel guides?
To get started, send the site address in Hampshire, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
How long does installation take at a site in Hampshire?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Do wheel guides damage tyres?
Correctly spaced wheel guides should not damage tyres. They are set slightly wider than the trailer track so the tyre only brushes the guide when the trailer is off line, and a flared entry stops tyres hitting the end. Guides that are bent or set too narrow should be corrected.
Can wheel guides be fitted to a tarmac yard?
Wheel guides can be fitted to a tarmac yard, but tarmac is usually too soft to hold anchors on its own. The normal approach is to cut out a strip and lay a concrete base for the guides. That work is identified at survey and included in the written quote.
Other services in Hampshire
Full guide to dock lights and wheel guides · All loading bay services in Hampshire