- Location
- Brighton, East Sussex
- Main postcode district
- BN2
- Nearby (straight line)
- Hove (1 mile), Portslade (3 miles) and Rottingdean (4 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
What matters for dock lights and wheel guides in Brighton?
Warehouses in Brighton loading deep trailers by forklift often find the back of the load hard to see without a dock light reaching into the trailer. Shelters and seals at sites near Brighton last longer when wheel guides keep trailers centred, because off-centre parking is a common cause of torn curtains.
A landlord preparing a unit in Brighton for re-letting can add dock lights and wheel guides at modest cost to make the bays more practical.
How does an installation in Brighton work? First, a free, no-obligation survey to measure up and understand the operation. Next, a fixed written quote. Then a programme agreed with you, so the work fits around deliveries, with out-of-hours slots if needed. The installation itself is carried out by specialist engineers who answer to us, and it finishes with testing, a walk-through for your staff and a handover pack.
Do health and safety rules cover dock lights and wheel guides?
Dock lights and wheel guides support your wider loading bay safety duties rather than replacing them. Once fitted, a dock light is work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so it must be suitable, maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
HSE's guide to workplace transport safety (HSG136) is the main reference for managing vehicles in the yard, and its loading guidance says there should be safeguards against drivers driving away too early, such as traffic lights, restraints or key control. Wheel guides and dock lights do not meet that requirement on their own, but they help drivers park accurately and help dock staff see what they are doing.
Electrical work for dock lights is carried out by qualified electricians and tested before use. The regulator is HSE in Great Britain and HSENI in Northern Ireland.
How much do dock lights and wheel guides cost?
Dock lights and wheel guides typically cost £280 to £950 per item, supplied and fitted, excluding VAT, where an item is one dock light or one wheel guide. A standard LED swing-arm light usually sits in the lower half of the range; long, heavy-section or cast-in guides sit towards the top.
What moves the price:
- Light specification: arm length, LED head output, protective guarding and whether a low-voltage supply is needed.
- Power: the distance to a suitable supply and how the cable is contained.
- Guide length and section: longer guides and heavier steel cost more.
- Yard surface: sound concrete takes anchors directly; tarmac usually needs a concrete base first, priced after survey.
- Number of bays: fitting several bays in one visit lowers the cost per item.
These are guide budgets. After a free site survey we send a written quote, which is the fixed price. VAT is added at the standard rate.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Gaps around trailers where heated or chilled air escapes
- Wind exposure at the dock, which affects door and shelter choice
- Control positions, isolators and any existing interlocks
- Bumper position and wear or damage on the dock face
- Dock height and the mix of trailers you load
- Access for deliveries, cranes or lifting equipment during installation
Options to discuss
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
Bolt-down wheel guides
Steel tube or channel guides fixed with resin anchors into an existing concrete apron, typically galvanised or painted in high-visibility colours for drivers using mirrors.
Which rules apply in England?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Brighton. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about dock lights and wheel guides in Brighton
Can you work outside our normal operating hours in Brighton?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Which building and safety rules apply to a site in Brighton?
It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Brighton, we check what applies at survey and design to it.
Will you deal with building control and planning for a project in Brighton?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
Do wheel guides damage tyres?
Correctly spaced wheel guides should not damage tyres. They are set slightly wider than the trailer track so the tyre only brushes the guide when the trailer is off line, and a flared entry stops tyres hitting the end. Guides that are bent or set too narrow should be corrected.
How long should wheel guides be?
Wheel guides need to be long enough to straighten the trailer before it reaches the bumpers, and the right length depends on your yard and approach. Tight yards where drivers turn late usually need longer guides with a flared entry. We set the length and spacing at survey.
Dock lights and wheel guides near Brighton
Nearby places we cover, measured from Brighton, include Hove (1 mile), Portslade (3 miles) and Rottingdean (4 miles). Ask if your own town is missing.
Other loading bay services in Brighton
Full guide to dock lights and wheel guides · Everything we do in Brighton
Tell us what is happening at your Brighton dock, what equipment is there and when it is used, and we will suggest the right next step.