- Location
- Chichester, West Sussex
- Main postcode district
- PO19
- Nearby (straight line)
- Bognor Regis (6 miles), Emsworth (7 miles) and Havant (9 miles)
- Survey and quote
- Free, with a fixed written quote
A vehicle restraint is a device at a loading bay that physically holds a trailer against the dock until it is safe to leave. In the UK most systems act on the rear wheel, either as a powered wheel-based restraint or a sensor wheel chock. Restraints guard against early drive-away and trailer creep, and are usually interlocked with the door and dock traffic lights.
How does this suit sites in Chichester?
Operators in Chichester reviewing their workplace transport risk assessment often look at restraints when key control alone has proved hard to enforce across shifts. New-build distribution sheds in Chichester can have restraint rails and ducting planned into the yard slab from the start, which is simpler than cutting them in later.
A warehouse in Chichester that already uses traffic lights may want to add restraints so the door cannot open until the trailer is physically held in place.
If you are planning vehicle restraints for a site in Chichester, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
Wheel-based or hook restraint: which suits UK trailers?
Wheel-based restraints and sensor wheel chocks suit most UK trailers, because they act on the rear wheel rather than on the back of the vehicle. Hook restraints, which catch the rear impact guard (sometimes called an ICC bar), are common elsewhere but suit fewer UK fleets.
- Wheel-based restraint: a steel guide rail fixed to the yard, with an arm or chock that moves against the rear wheel, either powered or pushed into place by the operative. It works regardless of tail lifts or underrun guard design.
- Sensor wheel chock: a heavy chock placed in front of the wheel, with a sensor or parking station that tells the dock controls it is in position. Lower cost and minimal groundwork, but it relies on someone placing it each time.
- Hook restraint: mounted on the dock face and hooking the rear guard. UK and European trailers vary widely at the rear, and tail lifts often get in the way, so this type needs checking against your actual fleet.
How much does a vehicle restraint cost?
A vehicle restraint typically costs £4,200 to £9,800 per bay, supplied and installed, excluding VAT. Sensor wheel chocks linked to the dock controls usually sit towards the lower end, and fully automatic wheel-based restraints with rail and interlocks towards the upper end.
What moves the price:
- Restraint type: a sensor chock needs far less hardware and groundwork than a powered, rail-mounted wheel restraint.
- Yard condition: rail-mounted units need a sound, level concrete apron. Broken concrete or tarmac may need a new base, priced after survey.
- Cabling: the distance from the restraint to the dock control panel, and whether ducts must be cut into the yard.
- Integration: linking to existing door and leveller controls is simpler on modern panels; older panels may need replacing.
- Number of bays and working hours: several bays in one project spread set-up costs, while out-of-hours work adds cost.
All figures are guide budgets. After a free site survey we send a written quote, and that quote is the fixed price. VAT is added at the standard rate.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Escape routes and pedestrian doors close to the bay
- Age and condition of the equipment already in place
- Dock height and the mix of trailers you load
- Yard gradient and the slope of the approach to the dock
- How drivers are prevented from pulling away too early
- Asbestos register and any other site hazard information
Options to discuss
Automatic wheel-based restraint
A powered arm on a yard-mounted rail that locates against the rear wheel at the push of a button and signals the dock controls once the trailer is held.
Hook restraint
A dock-mounted hook that catches the trailer's rear impact guard. Only suitable where your fleet has compatible rear guards, which we check carefully at survey.
What do the rules in England mean for the work?
Workplace safety in England is regulated by HSE. For a loading bay in Chichester, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about vehicle restraints in Chichester
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Chichester site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
How long does installation take at a site in Chichester?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Will you deal with building control and planning for a project in Chichester?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
What happens if a powered restraint loses power?
Powered restraints are normally designed with a manual release so a trailer is not trapped on the bay if power is lost. Your site procedure should say who is allowed to use the release and what checks they make first. We explain the release method at handover.
Is a vehicle restraint a legal requirement?
Not in every case: HSE guidance (followed by HSENI in Northern Ireland) says there should be safeguards against drivers driving away too early, and a vehicle restraint is one of the measures it lists. Traffic lights and the person in charge keeping keys or paperwork are the others. Which measures you use should follow your risk assessment. In Northern Ireland the regulator is HSENI.
Vehicle restraints near Chichester
Distances are measured from Chichester. Nearby towns we cover include Bognor Regis (6 miles), Emsworth (7 miles) and Havant (9 miles), and other towns in the area are covered too.
Other loading bay services in Chichester
Full guide to vehicle restraints · Everything we do in Chichester
Use the quote tool to tell us about the doors, levellers or shelters at your Chichester site, and we will be in touch to arrange the next step.