- Location
- Yarm, North Yorkshire
- Main postcode district
- TS15
- Nearby (straight line)
- Thornaby-on-Tees (3 miles), Stockton-on-Tees (5 miles) and Billingham (6 miles)
- Survey and quote
- Free, with a fixed written quote
A vehicle restraint is a device at a loading bay that physically holds a trailer against the dock until it is safe to leave. In the UK most systems act on the rear wheel, either as a powered wheel-based restraint or a sensor wheel chock. Restraints guard against early drive-away and trailer creep, and are usually interlocked with the door and dock traffic lights.
What matters for vehicle restraints in Yarm?
Multi-tenant logistics parks around Yarm can benefit from restraints when several tenants share yard space and trailers from different fleets arrive throughout the day. Third-party hauliers visiting sites in Yarm may not know each site's procedures, so a restraint that holds the wheel removes reliance on every driver following instructions.
Operators in Yarm reviewing their workplace transport risk assessment often look at restraints when key control alone has proved hard to enforce across shifts.
It starts with a free site survey in Yarm, where we measure the openings, check the dock and talk through how the bay is used. You then receive a fixed written quote. Once you accept, we manage the job: specialist installation engineers carry out the work under our management, planned around your deliveries, and out-of-hours working can be arranged. At handover we test everything with you and leave the documentation.
How does a vehicle restraint work with dock lights and interlocks?
A vehicle restraint is normally linked to the dock traffic lights and the door controls, so engaging the restraint is what allows loading to start.
A typical sequence looks like this:
- The trailer reverses on to the bay with the outside light on green and the door closed.
- The restraint engages the rear wheel. The outside light turns red for the driver and the inside light turns green for dock staff.
- The door can now be opened, and the leveller can only operate once the door is fully open.
- When loading is finished, the leveller is parked and the door closed before the restraint can release.
- The restraint releases, the outside light turns green and the driver can leave.
The exact interlocks depend on your equipment and risk assessment. See dock traffic lights and interlocks for the options on signals and control logic.
What does HSE guidance say about preventing drive-away?
HSE guidance says there must be safeguards to stop drivers driving away from a loading bay too early, and it lists vehicle or trailer restraints as one of the measures. The others it names are traffic lights and the person in charge keeping the vehicle keys or paperwork until it is safe to leave.
This comes from HSE's guide to workplace transport safety (HSG136) and its loading and unloading factsheet. The guidance sets out the outcome rather than one fixed solution, so the right combination for your site should follow your own risk assessment.
Once fitted, a restraint is work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so it must be suitable, maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999, and the regulator is HSENI rather than HSE.
Our guide to preventing drive-away and trailer creep compares the options side by side.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- How drivers are prevented from pulling away too early
- Lighting inside trailers and at the dock face
- Forklift and pallet truck loads crossing the leveller platform
- Temperature requirements for chilled, frozen or ambient goods
- Wall and steel structure for door, shelter and bumper fixings
- Access for deliveries, cranes or lifting equipment during installation
Options to discuss
Manual wheel-based restraint
The same rail-mounted principle with the restraint pushed into position by the operative. Lower cost than a powered unit, with a sensor to confirm engagement to the controls.
Hook restraint
A dock-mounted hook that catches the trailer's rear impact guard. Only suitable where your fleet has compatible rear guards, which we check carefully at survey.
What do the rules in England mean for the work?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Yarm. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about vehicle restraints in Yarm
Can you work alongside our main contractor on a new build in Yarm?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
What details do you need from us to quote for vehicle restraints?
To get started, send the site address in Yarm, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
How do you price vehicle restraints for a site in Yarm?
Guide budgets for supply and fit are £4,200 to £9,800 per bay, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
What happens if a powered restraint loses power?
Powered restraints are normally designed with a manual release so a trailer is not trapped on the bay if power is lost. Your site procedure should say who is allowed to use the release and what checks they make first. We explain the release method at handover.
Will a vehicle restraint slow down loading?
Engaging a restraint adds only a short step to each docking, and once it is part of the interlock sequence it becomes routine for dock staff. Many sites find that a clear sequence actually reduces delays, because there is less confusion about when it is safe to open the door or release the driver.
Vehicle restraints near Yarm
Distances are measured from Yarm. Nearby towns we cover include Thornaby-on-Tees (3 miles), Stockton-on-Tees (5 miles) and Billingham (6 miles), and other towns in the area are covered too.
Other loading bay services in Yarm
Full guide to vehicle restraints · Everything we do in Yarm
Start your enquiry for Yarm through the quote tool. A few photos and approximate sizes help us respond with something useful.