- Location
- Selby, North Yorkshire
- Main postcode district
- YO8
- Nearby (straight line)
- Goole (10 miles), Pontefract (12 miles) and York (12 miles)
- Survey and quote
- Free, with a fixed written quote
A vehicle restraint is a device at a loading bay that physically holds a trailer against the dock until it is safe to leave. In the UK most systems act on the rear wheel, either as a powered wheel-based restraint or a sensor wheel chock. Restraints guard against early drive-away and trailer creep, and are usually interlocked with the door and dock traffic lights.
How does this suit sites in Selby?
A warehouse in Selby that already uses traffic lights may want to add restraints so the door cannot open until the trailer is physically held in place. Operators in Selby reviewing their workplace transport risk assessment often look at restraints when key control alone has proved hard to enforce across shifts.
Yards around Selby that park uncoupled trailers at the dock can see trailers creep under forklift traffic, and a wheel-based restraint helps keep the leveller lip on the bed.
Your loading bay stays our responsibility from the survey to the handover. In Selby, the survey and written quote are free, and the quoted price is fixed for the agreed scope. Installation is carried out by specialist engineers working under our management, at times planned with you to protect your loading schedule. Out-of-hours work is available by arrangement. We finish by testing the equipment and handing over its documentation.
What happens on site when a vehicle restraint is installed?
Installing a vehicle restraint takes the bay out of use while the rail or chock station is fixed, cabled and tested, but neighbouring bays can usually keep working.
- Set out: the restraint position is marked in line with the bay so it meets the rear wheels of the trailers you receive.
- Fixing: rail-mounted units are anchored into the concrete apron. If a new concrete base is needed, it must cure before the restraint is fitted.
- Cabling: ducts are cut or laid from the restraint to the dock wall, and the control box is fitted inside next to the door.
- Connection: the restraint is wired into the door, leveller and traffic light controls so the sequence works as designed.
- Commissioning: the system is tested with a trailer on the bay, and dock staff are shown how to engage and release it.
We ask you to release the bay for the agreed period, confirm an electrical supply point, provide a trailer for commissioning and tell us about any buried services in the yard.
What does HSE guidance say about preventing drive-away?
HSE guidance says there must be safeguards to stop drivers driving away from a loading bay too early, and it lists vehicle or trailer restraints as one of the measures. The others it names are traffic lights and the person in charge keeping the vehicle keys or paperwork until it is safe to leave.
This comes from HSE's guide to workplace transport safety (HSG136) and its loading and unloading factsheet. The guidance sets out the outcome rather than one fixed solution, so the right combination for your site should follow your own risk assessment.
Once fitted, a restraint is work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so it must be suitable, maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999, and the regulator is HSENI rather than HSE.
Our guide to preventing drive-away and trailer creep compares the options side by side.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Temperature requirements for chilled, frozen or ambient goods
- Lighting inside trailers and at the dock face
- Dock height and the mix of trailers you load
- Drainage on recessed or sloping dock approaches
- Clear opening width and height for each door
- Scope to convert ground-level doors into docks or add lift tables
Options to discuss
Sensor wheel chock
A heavy-duty chock with a sensor or parking station that tells the dock controls when it is in place. Minimal groundwork and suited to retrofit on existing bays.
Trailer support stands
Stands placed under the front of an uncoupled semi-trailer to stop it dropping or tipping as forklifts drive on, used alongside a wheel restraint or chock.
Regulations and approvals in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Selby. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about vehicle restraints in Selby
Which building and safety rules apply to a site in Selby?
It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Selby, we check what applies at survey and design to it.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Selby site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Can you work outside our normal operating hours in Selby?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Can a vehicle restraint be fitted to an existing bay?
Yes, restraints are commonly retrofitted to existing bays. The main questions are whether the yard concrete in front of the bay is sound enough to anchor a rail, how cables will reach the dock controls, and whether the existing door and leveller panels can accept interlocks. Sensor chocks are often chosen where groundwork needs to be kept to a minimum.
Is a vehicle restraint a legal requirement?
Not in every case: HSE guidance (followed by HSENI in Northern Ireland) says there should be safeguards against drivers driving away too early, and a vehicle restraint is one of the measures it lists. Traffic lights and the person in charge keeping keys or paperwork are the others. Which measures you use should follow your risk assessment. In Northern Ireland the regulator is HSENI.
Vehicle restraints near Selby
Looking beyond Selby? Our pages for Goole (10 miles), Pontefract (12 miles) and York (12 miles) describe the same loading bay services and how to get in touch.
Other loading bay services in Selby
Full guide to vehicle restraints · Everything we do in Selby
Phone us to discuss your loading bay in Selby, or start with the online quote tool if you prefer to send details first.