- Location
- Northallerton, North Yorkshire
- Main postcode district
- DL6
- Nearby (straight line)
- Yarm (12 miles), Darlington (14 miles) and Thornaby-on-Tees (14 miles)
- Survey and quote
- Free, with a fixed written quote
A vehicle restraint is a device at a loading bay that physically holds a trailer against the dock until it is safe to leave. In the UK most systems act on the rear wheel, either as a powered wheel-based restraint or a sensor wheel chock. Restraints guard against early drive-away and trailer creep, and are usually interlocked with the door and dock traffic lights.
Why do sites in Northallerton choose this?
A warehouse in Northallerton that already uses traffic lights may want to add restraints so the door cannot open until the trailer is physically held in place. Operators in Northallerton reviewing their workplace transport risk assessment often look at restraints when key control alone has proved hard to enforce across shifts.
Restraint systems for sites in Northallerton are surveyed, quoted and installed in the same way as anywhere else in the UK, with a fixed price set out in writing.
If you are planning vehicle restraints for a site in Northallerton, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
How much does a vehicle restraint cost?
A vehicle restraint typically costs £4,200 to £9,800 per bay, supplied and installed, excluding VAT. Sensor wheel chocks linked to the dock controls usually sit towards the lower end, and fully automatic wheel-based restraints with rail and interlocks towards the upper end.
What moves the price:
- Restraint type: a sensor chock needs far less hardware and groundwork than a powered, rail-mounted wheel restraint.
- Yard condition: rail-mounted units need a sound, level concrete apron. Broken concrete or tarmac may need a new base, priced after survey.
- Cabling: the distance from the restraint to the dock control panel, and whether ducts must be cut into the yard.
- Integration: linking to existing door and leveller controls is simpler on modern panels; older panels may need replacing.
- Number of bays and working hours: several bays in one project spread set-up costs, while out-of-hours work adds cost.
All figures are guide budgets. After a free site survey we send a written quote, and that quote is the fixed price. VAT is added at the standard rate.
What does HSE guidance say about preventing drive-away?
HSE guidance says there must be safeguards to stop drivers driving away from a loading bay too early, and it lists vehicle or trailer restraints as one of the measures. The others it names are traffic lights and the person in charge keeping the vehicle keys or paperwork until it is safe to leave.
This comes from HSE's guide to workplace transport safety (HSG136) and its loading and unloading factsheet. The guidance sets out the outcome rather than one fixed solution, so the right combination for your site should follow your own risk assessment.
Once fitted, a restraint is work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so it must be suitable, maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999, and the regulator is HSENI rather than HSE.
Our guide to preventing drive-away and trailer creep compares the options side by side.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Dock height and the mix of trailers you load
- Condition of any existing leveller pit, kerb angles and pit drainage
- Temperature requirements for chilled, frozen or ambient goods
- Yard gradient and the slope of the approach to the dock
- Whether planning, building control or a building warrant may be needed
- Headroom above the opening and which track type will suit it
Options to discuss
Hook restraint
A dock-mounted hook that catches the trailer's rear impact guard. Only suitable where your fleet has compatible rear guards, which we check carefully at survey.
Manual wheel-based restraint
The same rail-mounted principle with the restraint pushed into position by the operative. Lower cost than a powered unit, with a sensor to confirm engagement to the controls.
Regulations and approvals in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Northallerton. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about vehicle restraints in Northallerton
Is VAT included in your guide prices for vehicle restraints?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in North Yorkshire as everywhere else: for vehicle restraints, it is £4,200 to £9,800 per bay, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
How do you price vehicle restraints for a site in Northallerton?
Guide budgets for supply and fit are £4,200 to £9,800 per bay, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Northallerton, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Will a vehicle restraint slow down loading?
Engaging a restraint adds only a short step to each docking, and once it is part of the interlock sequence it becomes routine for dock staff. Many sites find that a clear sequence actually reduces delays, because there is less confusion about when it is safe to open the door or release the driver.
What happens if a powered restraint loses power?
Powered restraints are normally designed with a manual release so a trailer is not trapped on the bay if power is lost. Your site procedure should say who is allowed to use the release and what checks they make first. We explain the release method at handover.
Vehicle restraints near Northallerton
If your site is not in Northallerton itself, it may be near one of these: Yarm (12 miles), Darlington (14 miles) and Thornaby-on-Tees (14 miles). Pick the closest.
Other loading bay services in Northallerton
Full guide to vehicle restraints · Everything we do in Northallerton
Send a few photos of the dock and a short description of the problem, and we will come back to you about your Northallerton site.