Vehicle restraints in Kent | Loading Bay Doors

In short

A vehicle restraint is a device at a loading bay that physically holds a trailer against the dock until it is safe to leave. In the UK most systems act on the rear wheel, either as a powered wheel-based restraint or a sensor wheel chock. Restraints guard against early drive-away and trailer creep, and are usually interlocked with the door and dock traffic lights.

How does this suit sites in Kent?

Operators in Kent reviewing their workplace transport risk assessment often look at restraints when key control alone has proved hard to enforce across shifts. New-build distribution sheds in Kent can have restraint rails and ducting planned into the yard slab from the start, which is simpler than cutting them in later.

Multi-tenant logistics parks around Kent can benefit from restraints when several tenants share yard space and trailers from different fleets arrive throughout the day.

Step one is a survey at your site in Kent, which costs nothing and carries no obligation. Step two is a written quote with a fixed price and a clear scope. Step three is installation, scheduled around your operation and carried out by specialist installation engineers working under our management, including evenings or weekends if agreed. Step four is handover, when the equipment is tested in front of you and the paperwork is passed over.

What happens on site when a vehicle restraint is installed?

Installing a vehicle restraint takes the bay out of use while the rail or chock station is fixed, cabled and tested, but neighbouring bays can usually keep working.

Set out: the restraint position is marked in line with the bay so it meets the rear wheels of the trailers you receive.
Fixing: rail-mounted units are anchored into the concrete apron. If a new concrete base is needed, it must cure before the restraint is fitted.
Cabling: ducts are cut or laid from the restraint to the dock wall, and the control box is fitted inside next to the door.
Connection: the restraint is wired into the door, leveller and traffic light controls so the sequence works as designed.
Commissioning: the system is tested with a trailer on the bay, and dock staff are shown how to engage and release it.

We ask you to release the bay for the agreed period, confirm an electrical supply point, provide a trailer for commissioning and tell us about any buried services in the yard.

Wheel-based or hook restraint: which suits UK trailers?

Wheel-based restraints and sensor wheel chocks suit most UK trailers, because they act on the rear wheel rather than on the back of the vehicle. Hook restraints, which catch the rear impact guard (sometimes called an ICC bar), are common elsewhere but suit fewer UK fleets.

Wheel-based restraint: a steel guide rail fixed to the yard, with an arm or chock that moves against the rear wheel, either powered or pushed into place by the operative. It works regardless of tail lifts or underrun guard design.
Sensor wheel chock: a heavy chock placed in front of the wheel, with a sensor or parking station that tells the dock controls it is in position. Lower cost and minimal groundwork, but it relies on someone placing it each time.
Hook restraint: mounted on the dock face and hooking the rear guard. UK and European trailers vary widely at the rear, and tail lifts often get in the way, so this type needs checking against your actual fleet.

Towns we cover in Kent

We cover vehicle restraints throughout Kent, and the towns below each have their own page. If yours is not listed, get in touch anyway.

Guide price

£4,200–£9,800 per bay, ex VAT

Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.

Which rules apply in England?

Workplace safety in England is regulated by HSE. For a loading bay in Kent, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.

Questions

Will you deal with building control and planning for a project in Kent?

We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.

Do you cover Kent for vehicle restraints?

Yes. We take on vehicle restraints for businesses in Kent and across Kent. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.

Can a vehicle restraint be fitted to an existing bay?

Yes, restraints are commonly retrofitted to existing bays. The main questions are whether the yard concrete in front of the bay is sound enough to anchor a rail, how cables will reach the dock controls, and whether the existing door and leveller panels can accept interlocks. Sensor chocks are often chosen where groundwork needs to be kept to a minimum.

Do vehicle restraints need servicing?

Yes. A restraint is work equipment under PUWER, so it must be maintained in a safe condition and inspected where wear could lead to danger. Servicing typically covers the rail and arm, sensors, controls and the interlock sequence with the door and lights.

Other services in Kent

Full guide to vehicle restraints · All loading bay services in Kent