Vehicle restraints in Gravesend

Location: Gravesend, Kent
Main postcode district: DA12
Nearby (straight line): Tilbury (2 miles), Grays (3 miles) and Strood (6 miles)
Survey and quote: Free, with a fixed written quote

Vehicle restraints, in short

A vehicle restraint is a device at a loading bay that physically holds a trailer against the dock until it is safe to leave. In the UK most systems act on the rear wheel, either as a powered wheel-based restraint or a sensor wheel chock. Restraints guard against early drive-away and trailer creep, and are usually interlocked with the door and dock traffic lights.

Is this right for your site in Gravesend?

Yards around Gravesend that park uncoupled trailers at the dock can see trailers creep under forklift traffic, and a wheel-based restraint helps keep the leveller lip on the bed. Restraint systems for sites in Gravesend are surveyed, quoted and installed in the same way as anywhere else in the UK, with a fixed price set out in writing.

Third-party hauliers visiting sites in Gravesend may not know each site's procedures, so a restraint that holds the wheel removes reliance on every driver following instructions.

Your loading bay stays our responsibility from the survey to the handover. In Gravesend, the survey and written quote are free, and the quoted price is fixed for the agreed scope. Installation is carried out by specialist engineers working under our management, at times planned with you to protect your loading schedule. Out-of-hours work is available by arrangement. We finish by testing the equipment and handing over its documentation.

Wheel-based or hook restraint: which suits UK trailers?

Wheel-based restraints and sensor wheel chocks suit most UK trailers, because they act on the rear wheel rather than on the back of the vehicle. Hook restraints, which catch the rear impact guard (sometimes called an ICC bar), are common elsewhere but suit fewer UK fleets.

Wheel-based restraint: a steel guide rail fixed to the yard, with an arm or chock that moves against the rear wheel, either powered or pushed into place by the operative. It works regardless of tail lifts or underrun guard design.
Sensor wheel chock: a heavy chock placed in front of the wheel, with a sensor or parking station that tells the dock controls it is in position. Lower cost and minimal groundwork, but it relies on someone placing it each time.
Hook restraint: mounted on the dock face and hooking the rear guard. UK and European trailers vary widely at the rear, and tail lifts often get in the way, so this type needs checking against your actual fleet.

How much does a vehicle restraint cost?

A vehicle restraint typically costs £4,200 to £9,800 per bay, supplied and installed, excluding VAT. Sensor wheel chocks linked to the dock controls usually sit towards the lower end, and fully automatic wheel-based restraints with rail and interlocks towards the upper end.

What moves the price:

Restraint type: a sensor chock needs far less hardware and groundwork than a powered, rail-mounted wheel restraint.
Yard condition: rail-mounted units need a sound, level concrete apron. Broken concrete or tarmac may need a new base, priced after survey.
Cabling: the distance from the restraint to the dock control panel, and whether ducts must be cut into the yard.
Integration: linking to existing door and leveller controls is simpler on modern panels; older panels may need replacing.
Number of bays and working hours: several bays in one project spread set-up costs, while out-of-hours work adds cost.

All figures are guide budgets. After a free site survey we send a written quote, and that quote is the fixed price. VAT is added at the standard rate.

Guide price, Gravesend

£4,200–£9,800 per bay, ex VAT

The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.

Survey checklist for your dock

Temperature requirements for chilled, frozen or ambient goods
Clear opening width and height for each door
How drivers are prevented from pulling away too early
Escape routes and pedestrian doors close to the bay
Age and condition of the equipment already in place
Condition of any existing leveller pit, kerb angles and pit drainage

Options to discuss

Trailer support stands

Stands placed under the front of an uncoupled semi-trailer to stop it dropping or tipping as forklifts drive on, used alongside a wheel restraint or chock.

Hook restraint

A dock-mounted hook that catches the trailer's rear impact guard. Only suitable where your fleet has compatible rear guards, which we check carefully at survey.

Which rules apply in England?

Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Gravesend. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.

Questions about vehicle restraints in Gravesend

Can you work alongside our main contractor on a new build in Gravesend?

Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.

Can you work outside our normal operating hours in Gravesend?

Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.

What details do you need from us to quote for vehicle restraints?

To get started, send the site address in Gravesend, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.

Will a vehicle restraint slow down loading?

Engaging a restraint adds only a short step to each docking, and once it is part of the interlock sequence it becomes routine for dock staff. Many sites find that a clear sequence actually reduces delays, because there is less confusion about when it is safe to open the door or release the driver.

What happens if a powered restraint loses power?

Powered restraints are normally designed with a manual release so a trailer is not trapped on the bay if power is lost. Your site procedure should say who is allowed to use the release and what checks they make first. We explain the release method at handover.

Vehicle restraints near Gravesend

If your site is not in Gravesend itself, it may be near one of these: Tilbury (2 miles), Grays (3 miles) and Strood (6 miles). Pick the closest.

Other loading bay services in Gravesend

Full guide to vehicle restraints · Everything we do in Gravesend

Request a quote for your loading bay in Gravesend, attaching photos of the dock, the equipment and any damage.