- Location
- Inverurie, Aberdeen and Aberdeenshire
- Main postcode district
- AB51
- Nearby (straight line)
- Westhill (10 miles), Aberdeen (14 miles) and Stonehaven (23 miles)
- Survey and quote
- Free, with a fixed written quote
A vehicle restraint is a device at a loading bay that physically holds a trailer against the dock until it is safe to leave. In the UK most systems act on the rear wheel, either as a powered wheel-based restraint or a sensor wheel chock. Restraints guard against early drive-away and trailer creep, and are usually interlocked with the door and dock traffic lights.
Where does this fit at a dock in Inverurie?
Restraint systems for sites in Inverurie are surveyed, quoted and installed in the same way as anywhere else in the UK, with a fixed price set out in writing. New-build distribution sheds in Inverurie can have restraint rails and ducting planned into the yard slab from the start, which is simpler than cutting them in later.
Operators in Inverurie reviewing their workplace transport risk assessment often look at restraints when key control alone has proved hard to enforce across shifts.
A single contact at Loading Bay Doors handles your project in Inverurie from start to finish. The free site survey and fixed written quote come first, with no obligation to proceed. We then book the installation for times that suit the operation, including out of hours by arrangement, and manage the specialist engineers on site. At the end we commission and test the equipment, walk your team through it and provide the documentation.
Wheel-based or hook restraint: which suits UK trailers?
Wheel-based restraints and sensor wheel chocks suit most UK trailers, because they act on the rear wheel rather than on the back of the vehicle. Hook restraints, which catch the rear impact guard (sometimes called an ICC bar), are common elsewhere but suit fewer UK fleets.
- Wheel-based restraint: a steel guide rail fixed to the yard, with an arm or chock that moves against the rear wheel, either powered or pushed into place by the operative. It works regardless of tail lifts or underrun guard design.
- Sensor wheel chock: a heavy chock placed in front of the wheel, with a sensor or parking station that tells the dock controls it is in position. Lower cost and minimal groundwork, but it relies on someone placing it each time.
- Hook restraint: mounted on the dock face and hooking the rear guard. UK and European trailers vary widely at the rear, and tail lifts often get in the way, so this type needs checking against your actual fleet.
How does a vehicle restraint work with dock lights and interlocks?
A vehicle restraint is normally linked to the dock traffic lights and the door controls, so engaging the restraint is what allows loading to start.
A typical sequence looks like this:
- The trailer reverses on to the bay with the outside light on green and the door closed.
- The restraint engages the rear wheel. The outside light turns red for the driver and the inside light turns green for dock staff.
- The door can now be opened, and the leveller can only operate once the door is fully open.
- When loading is finished, the leveller is parked and the door closed before the restraint can release.
- The restraint releases, the outside light turns green and the driver can leave.
The exact interlocks depend on your equipment and risk assessment. See dock traffic lights and interlocks for the options on signals and control logic.
The same published guide range applies across Scotland; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Traffic routes for vehicles and separation of pedestrians
- Escape routes and pedestrian doors close to the bay
- Control positions, isolators and any existing interlocks
- Asbestos register and any other site hazard information
- Bumper position and wear or damage on the dock face
- Dock height and the mix of trailers you load
Options to discuss
Sensor wheel chock
A heavy-duty chock with a sensor or parking station that tells the dock controls when it is in place. Minimal groundwork and suited to retrofit on existing bays.
Manual wheel-based restraint
The same rail-mounted principle with the restraint pushed into position by the operative. Lower cost than a powered unit, with a sensor to confirm engagement to the controls.
What do the rules in Scotland mean for the work?
Doors and dock equipment installed in Scotland may carry the UKCA or the CE mark, and we pass on the documentation for everything fitted in Inverurie. Because building warrant and planning questions can affect the programme, we check what applies at survey and raise any approvals early rather than assuming none are needed.
Questions about vehicle restraints in Inverurie
How long does installation take at a site in Inverurie?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Can you work outside our normal operating hours in Inverurie?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Do you cover Inverurie for vehicle restraints?
Yes. We take on vehicle restraints for businesses in Inverurie and across Aberdeen and Aberdeenshire. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
Do vehicle restraints work with all trailers?
Wheel-based restraints and sensor chocks work with most trailers, because they act on the rear wheel rather than on the back of the vehicle. Vehicles with unusual wheel positions or very small wheels need checking, so we look at the vehicles you receive during the survey.
Do vehicle restraints need servicing?
Yes. A restraint is work equipment under PUWER, so it must be maintained in a safe condition and inspected where wear could lead to danger. Servicing typically covers the rail and arm, sensors, controls and the interlock sequence with the door and lights.
Vehicle restraints near Inverurie
We also cover towns near Inverurie, including Westhill (10 miles), Aberdeen (14 miles) and Stonehaven (23 miles). Each has its own page with the same services and process.
Other loading bay services in Inverurie
Full guide to vehicle restraints · Everything we do in Inverurie
Whether it is a new bay or a fault on an existing one, call us or request a quote for your site in Inverurie.