- Location
- Ashford, Surrey
- Main postcode district
- TW15
- Nearby (straight line)
- Staines (2 miles), Feltham (2 miles) and Sunbury-on-Thames (3 miles)
- Survey and quote
- Free, with a fixed written quote
A sectional loading bay door is an overhead door made from horizontal insulated steel panels hinged together, which run up on rollers in side tracks and park beneath the ceiling or up the wall when open. Panels are commonly 40 to 80 mm thick, so the door seals and insulates better than a single-skin shutter, and it can be operated by hand chain, push-up or electric motor.
Is this right for your site in Ashford?
Ageing units around Ashford sometimes have low lintels or pipework above the opening, which a low-headroom or high-lift track can be chosen to work around. A dock facing the prevailing wind, wherever it sits in Ashford, benefits from a well-sealed sectional door that stops rain and draughts reaching the loading area.
If you are fitting out a new warehouse in Ashford, specifying insulated sectional doors from the start avoids disruptive changes once the building is occupied.
A single contact at Loading Bay Doors handles your project in Ashford from start to finish. The free site survey and fixed written quote come first, with no obligation to proceed. We then book the installation for times that suit the operation, including out of hours by arrangement, and manage the specialist engineers on site. At the end we commission and test the equipment, walk your team through it and provide the documentation.
How much does a sectional loading bay door cost?
A sectional loading bay door typically costs £2,400 to £5,200 per door, excluding VAT, supply and fit, for a made-to-measure insulated door fitted and working.
Where your door lands in the range depends on:
- Opening size: larger doors need more panel area, heavier springs and longer track.
- Panel thickness and finish: thicker insulated panels and non-standard colours add cost.
- Track type: high-lift and vertical lift tracks use more steel and fixings than standard lift.
- Operation: an electric operator with safety edge and photocells costs more than chain or push-up operation.
- Vision panels and extras: glazed sections, interlocks to the leveller and links to traffic lights.
- Site conditions: removing an old door, making good the opening, getting power to the door head and out-of-hours working.
We price after a free site survey, and the written quote is the fixed price for the work described. You can compare typical figures on our price guide.
What happens on site when a sectional dock door is installed?
Fitting a sectional dock door often takes around a day per opening once the door is on site, though very large doors or awkward fixings take longer. The bay is out of use while the work is under way.
A typical installation runs like this:
- The old door, if there is one, is taken down and removed from site.
- Steel angles or packers are fixed to the opening so the tracks run true.
- Tracks, springs and panels are assembled and the door is balanced.
- The operator, safety edge, photocells and controls are fitted and wired.
- The door is tested, adjusted and handed over.
Before we arrive you will need a clear area inside the opening for access equipment and the bay taken out of service. Electric doors also need a suitable isolated power supply near the door head, single or three-phase depending on the operator, which we confirm in the quote. On multi-door sites we work bay by bay so the rest of the dock keeps running.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Age and condition of the equipment already in place
- Headroom above the opening and which track type will suit it
- Clear opening width and height for each door
- Access for deliveries, cranes or lifting equipment during installation
- Power supply at each bay, including three-phase availability
- Wind exposure at the dock, which affects door and shelter choice
Options to discuss
Push-up or hand chain operation
Push-up suits small, light doors, while a hand chain makes heavier dock doors easy to open. Both suit bays used a few times a day and need no power supply.
Electric operator
A shaft-mounted or trolley operator with push-button controls, safety edge and photocells. Suits busy bays and can be interlocked with levellers, shelters and traffic lights.
Regulations and approvals in England
In England, Approved Document L (2021) sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. That shapes door specification for sites in Ashford, so we confirm the requirement for your project and check what applies at survey before recommending a door.
Questions about sectional loading bay doors in Ashford
Will you deal with building control and planning for a project in Ashford?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
What details do you need from us to quote for sectional loading bay doors?
To get started, send the site address in Ashford, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Is the site survey in Ashford free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
What panel thickness should we choose for a heated warehouse?
For most heated warehouses a panel at the thicker end of the common 40 to 80 mm range is the sensible starting point, because it insulates better. Thinner panels can suit unheated stores. New and replacement doors also need to meet the energy rules for your nation, which we check when specifying.
Can the door be supplied in our company colours?
Yes, panels come in a range of standard colours, and many manufacturers can supply other shades at extra cost and with a longer lead time. The inside face is usually white or light grey. We confirm the colour, finish and lead time in the written quote.
Sectional loading bay doors near Ashford
Distances are measured from Ashford. Nearby towns we cover include Staines (2 miles), Feltham (2 miles) and Sunbury-on-Thames (3 miles), and other towns in the area are covered too.
Other loading bay services in Ashford
Full guide to sectional loading bay doors · Everything we do in Ashford
Have photos of the door, leveller or shelter? Send them with your enquiry and we can give a clearer answer for your Ashford site.