- Location
- Chorley, Lancashire
- Main postcode district
- PR7
- Nearby (straight line)
- Leyland (4 miles), Darwen (7 miles) and Wigan (7 miles)
- Survey and quote
- Free, with a fixed written quote
A sectional loading bay door is an overhead door made from horizontal insulated steel panels hinged together, which run up on rollers in side tracks and park beneath the ceiling or up the wall when open. Panels are commonly 40 to 80 mm thick, so the door seals and insulates better than a single-skin shutter, and it can be operated by hand chain, push-up or electric motor.
Why do sites in Chorley choose this?
A dock facing the prevailing wind, wherever it sits in Chorley, benefits from a well-sealed sectional door that stops rain and draughts reaching the loading area. Warehouses across Chorley that still rely on single-skin shutters may switch to insulated sectional doors when heating costs or cold goods-in areas become a problem.
Food and drink businesses in Chorley running temperature-controlled goods-in areas can choose thicker panels to hold conditions steady between deliveries.
Your loading bay stays our responsibility from the survey to the handover. In Chorley, the survey and written quote are free, and the quoted price is fixed for the agreed scope. Installation is carried out by specialist engineers working under our management, at times planned with you to protect your loading schedule. Out-of-hours work is available by arrangement. We finish by testing the equipment and handing over its documentation.
Do sectional loading bay doors have to meet energy and safety rules?
Yes. New and replacement sectional loading bay doors fall under building energy rules and workplace safety law, and the detail differs between the four nations.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. Wales, Scotland and Northern Ireland each have their own energy rules, and we confirm the figure that applies to your nation and project.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Workplace (Health, Safety and Welfare) Regulations (Northern Ireland) 1993, require upward-opening doors to have a device that stops them falling back. On a sectional door that usually means spring break and cable break protection.
- Product standard: BS EN 13241 is the product standard for industrial doors, and powered doors are also assessed against BS EN 12453 for safety in use.
- Marking: a powered door in Great Britain may be UKCA or CE marked, while in Northern Ireland it is the CE mark, or CE with UKNI, that applies.
What happens on site when a sectional dock door is installed?
Fitting a sectional dock door often takes around a day per opening once the door is on site, though very large doors or awkward fixings take longer. The bay is out of use while the work is under way.
A typical installation runs like this:
- The old door, if there is one, is taken down and removed from site.
- Steel angles or packers are fixed to the opening so the tracks run true.
- Tracks, springs and panels are assembled and the door is balanced.
- The operator, safety edge, photocells and controls are fitted and wired.
- The door is tested, adjusted and handed over.
Before we arrive you will need a clear area inside the opening for access equipment and the bay taken out of service. Electric doors also need a suitable isolated power supply near the door head, single or three-phase depending on the operator, which we confirm in the quote. On multi-door sites we work bay by bay so the rest of the dock keeps running.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Gaps around trailers where heated or chilled air escapes
- Asbestos register and any other site hazard information
- Traffic routes for vehicles and separation of pedestrians
- Dock height and the mix of trailers you load
- How often each door cycles during a typical shift
- Whether planning, building control or a building warrant may be needed
Options to discuss
Electric operator
A shaft-mounted or trolley operator with push-button controls, safety edge and photocells. Suits busy bays and can be interlocked with levellers, shelters and traffic lights.
Push-up or hand chain operation
Push-up suits small, light doors, while a hand chain makes heavier dock doors easy to open. Both suit bays used a few times a day and need no power supply.
Which rules apply in England?
Workplace safety in England is regulated by HSE. For a loading bay in Chorley, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about sectional loading bay doors in Chorley
What details do you need from us to quote for sectional loading bay doors?
To get started, send the site address in Chorley, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Can you work outside our normal operating hours in Chorley?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Is the site survey in Chorley free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
What panel thickness should we choose for a heated warehouse?
For most heated warehouses a panel at the thicker end of the common 40 to 80 mm range is the sensible starting point, because it insulates better. Thinner panels can suit unheated stores. New and replacement doors also need to meet the energy rules for your nation, which we check when specifying.
How is a sectional loading bay door locked?
A manual sectional door is usually locked with a slide bolt or shoot bolt on the inside, while an electric door is held closed by its operator. Because dock doors are secured from inside the building, extra locks are not often needed, but we can add bolts or a locking operator where security is a priority.
Sectional loading bay doors near Chorley
We also cover towns near Chorley, including Leyland (4 miles), Darwen (7 miles) and Wigan (7 miles). Each has its own page with the same services and process.
Other loading bay services in Chorley
Full guide to sectional loading bay doors · Everything we do in Chorley
Use the quote tool to tell us about the doors, levellers or shelters at your Chorley site, and we will be in touch to arrange the next step.