- Location
- Hawick, Scottish Borders
- Main postcode district
- TD9
- Nearby (straight line)
- Galashiels (13 miles) and Peebles (22 miles)
- Survey and quote
- Free, with a fixed written quote
A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
Where does this fit at a dock in Hawick?
Unheated stores and trade counters in Hawick can suit a single-skin steel shutter, giving a secure dock door at a lower cost than an insulated sectional door. If a manual shutter on a site in Hawick is hard work to open several times a day, a new electric shutter or a retrofit motor may solve it.
Where a site in Hawick is exposed to salt air or regular washdown, aluminium laths or a good powder coat help slow corrosion on the curtain and guides.
Step one is a survey at your site in Hawick, which costs nothing and carries no obligation. Step two is a written quote with a fixed price and a clear scope. Step three is installation, scheduled around your operation and carried out by specialist installation engineers working under our management, including evenings or weekends if agreed. Step four is handover, when the equipment is tested in front of you and the paperwork is passed over.
Is a roller shutter or a sectional door better for a loading bay?
A roller shutter is usually better where headroom is tight, budgets are limited or the building is unheated, while a sectional door is usually better for heated buildings and busy docks that open and close all day.
- Headroom: a shutter coils into a box above the opening; a sectional door needs track running back under the ceiling or up the wall.
- Insulation: insulated sectional panels generally outperform insulated laths.
- Speed: shutters are slower to open and close than most electric sectional doors.
- Security: a closed steel shutter is a robust barrier.
- Repairs: damaged laths can be replaced individually, just as a dented sectional panel can be swapped.
See sectional loading bay doors to compare the two. Where either would work, we can quote both so you can weigh price against performance.
What safety and energy rules apply to roller shutters at a dock?
A dock roller shutter must be protected against falling, must not trap anyone if powered, and in a heated building may need insulated laths to meet energy rules.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Northern Ireland regulations of 1993, require upward-opening doors to have a device that stops them falling back. On a shutter this is usually a safety brake or anti-fall device on the barrel.
- Trapping: powered shutters need suitable features to prevent trapping, typically a safety edge and photocells, and a way to open by hand, such as a chain override, where needed.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access doors in new and replacement work. A single-skin steel shutter will not normally reach that figure. Wales, Scotland and Northern Ireland set their own rules, and we confirm the figure for your nation and project.
Our guide to energy rules for loading bay doors explains U-values in more detail.
The same published guide range applies across Scotland; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- How often each door cycles during a typical shift
- Headroom above the opening and which track type will suit it
- Clear opening width and height for each door
- Access for deliveries, cranes or lifting equipment during installation
- Age and condition of the equipment already in place
- Scope to convert ground-level doors into docks or add lift tables
Options to discuss
Electric operation with safety devices
An external or tubular motor with push-button controls, safety edge, photocells and a hand-chain override for use during a power cut.
Wind-resistant build
End locks, deeper guides and heavier gauge laths for wide or exposed openings where gusts could pull the curtain out of its guides.
What do the rules in Scotland mean for the work?
Doors and dock equipment installed in Scotland may carry the UKCA or the CE mark, and we pass on the documentation for everything fitted in Hawick. Because building warrant and planning questions can affect the programme, we check what applies at survey and raise any approvals early rather than assuming none are needed.
Questions about roller shutter loading bay doors in Hawick
Do you cover Hawick for roller shutter loading bay doors?
Yes. We take on roller shutter loading bay doors for businesses in Hawick and across the Scottish Borders. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Hawick, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
What details do you need from us to quote for roller shutter loading bay doors?
To get started, send the site address in Hawick, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Can individual damaged laths be replaced?
Yes, damaged laths can usually be cut out and replaced without changing the whole curtain, provided matching laths are still available. If damage spreads across many laths or the guides are bent, a new curtain is often more economical. Lath repairs are carried out on a chargeable visit with the price agreed first.
Are roller shutters noisy at a loading bay?
A roller shutter is generally noisier than a sectional door because the laths move against each other as they coil, though insulated laths and well-adjusted guides reduce this. Noise matters most where the dock is close to offices or neighbours. Keeping the barrel and guides clean and lubricated keeps running noise down.
Roller shutter loading bay doors near Hawick
If your site is not in Hawick itself, it may be near one of these: Galashiels (13 miles) and Peebles (22 miles). Pick the closest.
Other loading bay services in Hawick
Full guide to roller shutter loading bay doors · Everything we do in Hawick
If a loading bay in Hawick needs attention, call us or send photos and details online.