A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
What should sites in the Scottish Borders consider?
Timber yards and builders merchants in the Scottish Borders handling long loads and heavy forklift traffic can benefit from strong steel shutters that tolerate knocks. Low headroom is the deciding factor at many older buildings, whether in the Scottish Borders or elsewhere, and a compact roller shutter avoids overhead tracks altogether.
Docks that face an open yard in the Scottish Borders can catch strong gusts, so we check orientation and specify end locks and heavier laths where exposure calls for it.
Our part of the job in the Scottish Borders is to survey, quote and manage; the fitting itself is done by specialist installation engineers working under our management. The survey and the written quote are free. Once the fixed price is accepted, we agree dates that work around your deliveries and shifts, including out-of-hours working where needed. Every installation is tested before handover, and you receive the documentation for each item fitted.
What safety and energy rules apply to roller shutters at a dock?
A dock roller shutter must be protected against falling, must not trap anyone if powered, and in a heated building may need insulated laths to meet energy rules.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Northern Ireland regulations of 1993, require upward-opening doors to have a device that stops them falling back. On a shutter this is usually a safety brake or anti-fall device on the barrel.
- Trapping: powered shutters need suitable features to prevent trapping, typically a safety edge and photocells, and a way to open by hand, such as a chain override, where needed.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access doors in new and replacement work. A single-skin steel shutter will not normally reach that figure. Wales, Scotland and Northern Ireland set their own rules, and we confirm the figure for your nation and project.
Our guide to energy rules for loading bay doors explains U-values in more detail.
How is a roller shutter fitted to an existing loading bay opening?
A roller shutter is fitted either behind the opening on the inside face or between the reveals, with guides fixed down each side and the barrel mounted on brackets above. Fitting usually takes a day or less per opening once the shutter is on site.
The work normally includes:
- Removing and disposing of the old door or shutter.
- Checking the lintel and reveals will take the fixings, and adding steel packers if not.
- Fixing the guides, brackets and barrel, then running the curtain onto the barrel.
- Fitting the motor, controls, safety edge and photocells on electric shutters.
- Setting limits, testing the safety brake and demonstrating the manual override.
You will need to clear the area inside the opening and take the bay out of use. An electric shutter also needs a suitable isolated power supply near the barrel, which we can include in the quote if one is not already there.
Towns we cover in the Scottish Borders
Find your town in the list below for details of roller shutter loading bay doors across the Scottish Borders, or contact us if your location is not shown.
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
What do the rules in Scotland mean for the work?
Doors and dock equipment installed in Scotland may carry the UKCA or the CE mark, and we pass on the documentation for everything fitted in the Scottish Borders. Because building warrant and planning questions can affect the programme, we check what applies at survey and raise any approvals early rather than assuming none are needed.
Questions
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in the Scottish Borders, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Can you work alongside our main contractor on a new build in the Scottish Borders?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
What finish options are available?
Most dock shutters are supplied in galvanised steel or powder-coated in a standard colour, with other colours available at extra cost. A hood box over the coil protects it from dust and weather and gives a tidier finish inside. We confirm finish and colour in the written quote.
How long does a new roller shutter take to arrive?
Shutters are made to measure, so the lead time depends on size, lath type and finish, and we confirm it in the written quote. The existing door stays in use until the new shutter is ready, and installation is then booked for a time that suits your operation.
Other services in the Scottish Borders
Full guide to roller shutter loading bay doors · All loading bay services in the Scottish Borders