A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
Is this right for your site in Moray?
Low headroom is the deciding factor at many older buildings, whether in Moray or elsewhere, and a compact roller shutter avoids overhead tracks altogether. Every shutter we quote for a building in Moray starts with a survey of the opening, the space above it and how often the door will run.
Timber yards and builders merchants in Moray handling long loads and heavy forklift traffic can benefit from strong steel shutters that tolerate knocks.
A single contact at Loading Bay Doors handles your project in Moray from start to finish. The free site survey and fixed written quote come first, with no obligation to proceed. We then book the installation for times that suit the operation, including out of hours by arrangement, and manage the specialist engineers on site. At the end we commission and test the equipment, walk your team through it and provide the documentation.
What safety and energy rules apply to roller shutters at a dock?
A dock roller shutter must be protected against falling, must not trap anyone if powered, and in a heated building may need insulated laths to meet energy rules.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Northern Ireland regulations of 1993, require upward-opening doors to have a device that stops them falling back. On a shutter this is usually a safety brake or anti-fall device on the barrel.
- Trapping: powered shutters need suitable features to prevent trapping, typically a safety edge and photocells, and a way to open by hand, such as a chain override, where needed.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access doors in new and replacement work. A single-skin steel shutter will not normally reach that figure. Wales, Scotland and Northern Ireland set their own rules, and we confirm the figure for your nation and project.
Our guide to energy rules for loading bay doors explains U-values in more detail.
Which lath should I choose: single skin, insulated or aluminium?
Choose single-skin steel for unheated buildings where cost and strength matter most, insulated laths where the building is heated, and aluminium where weight or corrosion is the main concern.
- Single-skin steel: strong and economical, ideal for unheated stores, trade counters and secure external openings, but it offers little insulation.
- Insulated steel laths: twin-skin laths filled with foam improve thermal performance and reduce noise. The coil is larger, so the box above the opening is bigger.
- Aluminium laths: lighter and corrosion resistant, useful in coastal or washdown environments, and easier on the motor at large openings.
- Perforated or punched laths: let light and air through while keeping the opening secure, better suited to internal cages than external docks.
Lath gauge and profile matter too. Heavier gauges resist forklift knocks and wind better, and we specify them for wide or exposed openings.
Towns we cover in Moray
We take enquiries about roller shutter loading bay doors from across Moray. These are the towns with their own pages:
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
What do the rules in Scotland mean for the work?
Doors and dock equipment installed in Scotland may carry the UKCA or the CE mark, and we pass on the documentation for everything fitted in Moray. Because building warrant and planning questions can affect the programme, we check what applies at survey and raise any approvals early rather than assuming none are needed.
Questions
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Moray site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Is VAT included in your guide prices for roller shutter loading bay doors?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Moray as everywhere else: for roller shutter loading bay doors, it is £1,600 to £4,800 per door, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Do roller shutters work on cold store docks?
Roller shutters are rarely used as the main door on a cold store dock, because even insulated laths do not hold temperature as well as a purpose-made cold store door. They can work as an outer security door in front of an insulated door, or at ambient bays on the same site.
Can individual damaged laths be replaced?
Yes, damaged laths can usually be cut out and replaced without changing the whole curtain, provided matching laths are still available. If damage spreads across many laths or the guides are bent, a new curtain is often more economical. Lath repairs are carried out on a chargeable visit with the price agreed first.
Other services in Moray
Full guide to roller shutter loading bay doors · All loading bay services in Moray