A sectional loading bay door is an overhead door made from horizontal insulated steel panels hinged together, which run up on rollers in side tracks and park beneath the ceiling or up the wall when open. Panels are commonly 40 to 80 mm thick, so the door seals and insulates better than a single-skin shutter, and it can be operated by hand chain, push-up or electric motor.
Is this right for your site in Moray?
Ageing units around Moray sometimes have low lintels or pipework above the opening, which a low-headroom or high-lift track can be chosen to work around. A dock facing the prevailing wind, wherever it sits in Moray, benefits from a well-sealed sectional door that stops rain and draughts reaching the loading area.
Food and drink businesses in Moray running temperature-controlled goods-in areas can choose thicker panels to hold conditions steady between deliveries.
Here is what happens after you contact us about a site in Moray. We arrange a free survey, measure up and send a fixed written quote. If you go ahead, we manage the whole job, including ordering, delivery and coordination with your site team. Specialist installation engineers working under our management do the fitting, at times built around your loading schedule, with out-of-hours work by arrangement. Testing and handover documents close the job.
Do sectional loading bay doors have to meet energy and safety rules?
Yes. New and replacement sectional loading bay doors fall under building energy rules and workplace safety law, and the detail differs between the four nations.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. Wales, Scotland and Northern Ireland each have their own energy rules, and we confirm the figure that applies to your nation and project.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Workplace (Health, Safety and Welfare) Regulations (Northern Ireland) 1993, require upward-opening doors to have a device that stops them falling back. On a sectional door that usually means spring break and cable break protection.
- Product standard: BS EN 13241 is the product standard for industrial doors, and powered doors are also assessed against BS EN 12453 for safety in use.
- Marking: a powered door in Great Britain may be UKCA or CE marked, while in Northern Ireland it is the CE mark, or CE with UKNI, that applies.
Should a sectional dock door have vision panels or a wicket door?
Vision panels are worth adding on most dock doors, while wicket doors are rarely used on loading bays. A row of double-glazed windows lets staff see whether a trailer is on the bay and brings daylight into the dock area.
- Vision panels can be a single row at eye level or fully glazed sections in aluminium frames.
- Glazed sections lower the door's insulation, so on a heated or chilled building we balance daylight against thermal performance.
- Wicket doors are uncommon on docks because there is a trailer or a drop to the yard behind the door, so they rarely offer a safe exit. A separate pedestrian door beside the bay is usually the better answer.
It is also worth deciding now whether the door will be interlocked with the leveller, so the lip cannot be raised until the door is fully open. Adding links like this later is harder.
Towns we cover in Moray
Below is a list of towns in Moray for sectional loading bay doors. Each page explains our approach for sites in that town.
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
Regulations and approvals in Scotland
HSE is the workplace safety regulator in Scotland. At a loading bay in Moray, doors need to satisfy regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, dock equipment must be kept safe under PUWER, and drivers must be prevented from pulling away too early. We check what applies at survey.
Questions
What details do you need from us to quote for sectional loading bay doors?
To get started, send the site address in Moray, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
How do you price sectional loading bay doors for a site in Moray?
Guide budgets for supply and fit are £2,400 to £5,200 per door, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
What panel thickness should we choose for a heated warehouse?
For most heated warehouses a panel at the thicker end of the common 40 to 80 mm range is the sensible starting point, because it insulates better. Thinner panels can suit unheated stores. New and replacement doors also need to meet the energy rules for your nation, which we check when specifying.
Can the door be supplied in our company colours?
Yes, panels come in a range of standard colours, and many manufacturers can supply other shades at extra cost and with a longer lead time. The inside face is usually white or light grey. We confirm the colour, finish and lead time in the written quote.
Other services in Moray
Full guide to sectional loading bay doors · All loading bay services in Moray