- Location
- Leatherhead, Surrey
- Main postcode district
- KT22
- Nearby (straight line)
- Epsom (4 miles), Dorking (4 miles) and Esher (5 miles)
- Survey and quote
- Free, with a fixed written quote
Dock lights and wheel guides are two simple loading bay aids. A dock light is a lamp, usually LED, on a swing arm beside the dock door that shines into the trailer so forklift drivers can see the load. Wheel guides are steel rails fixed to the yard that steer the rear wheels so the trailer arrives straight and centred on the leveller.
Where does this fit at a dock in Leatherhead?
Any site in Leatherhead considering these items gets the same survey and fixed written quote that we provide across England, Scotland, Wales and Northern Ireland. Warehouses in Leatherhead loading deep trailers by forklift often find the back of the load hard to see without a dock light reaching into the trailer.
Tight yards in Leatherhead where drivers reverse between parked trailers or around buildings make wheel guides especially useful for getting the trailer straight first time.
Keeping the dock running is usually the first concern, so we plan around it. After a free survey of your Leatherhead site and a written quote at a fixed price, we agree when each bay can be released and whether any work should happen out of hours. Specialist installation engineers working under our management then fit the equipment, and we test it and hand over the documentation before the bay goes back into use.
How do wheel guides protect shelters, seals and levellers?
Wheel guides protect dock equipment by keeping every trailer centred on the bay, so contact forces land where the equipment is designed to take them. A trailer that parks off-centre loads one side of the dock much harder than the other.
- Shelters: off-centre trailers catch the side curtains and frame, causing tears and bent arms.
- Seals: one pad is crushed while the other barely touches, leaving gaps for draughts and rain.
- Levellers: the lip can land near the edge of the trailer bed, with less support for forklifts.
- Bumpers: one bumper takes every impact and wears out early.
Dock lights help in a different way: forklift drivers who can see clearly inside the trailer are less likely to strike the trailer walls or the door frame on the way out. Combining guides and lights with correctly positioned dock bumpers gives a well-protected bay.
What happens on site when dock lights or wheel guides are fitted?
Dock lights are fitted from inside the building and usually leave the bay usable for most of the work, while wheel guides close the bay to vehicles until the anchors have cured.
- Dock lights: the bracket is fixed beside the door, the arm and head fitted, and the supply connected and tested. The circuit is isolated briefly during connection.
- Wheel guides: the yard in front of the bay is coned off, guides are set out, drilled and anchored, and the resin is left to cure before trailers return.
- Concrete bases: where tarmac needs a concrete strip first, the bay stays closed until the concrete has gained enough strength.
We ask you to provide a clear bay, details of the nearest power supply, safe yard access and someone who can manage vehicle movements around the work area. Planning guide installation for a quieter period keeps disruption to a minimum.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- How drivers are prevented from pulling away too early
- How often each door cycles during a typical shift
- Headroom above the opening and which track type will suit it
- Drainage on recessed or sloping dock approaches
- Scope to convert ground-level doors into docks or add lift tables
- Traffic routes for vehicles and separation of pedestrians
Options to discuss
Cast-in wheel guides
Guides set into new concrete with embedded anchors during yard works, giving a very strong fixing for new-build docks, resurfaced yards and loading bay conversions.
Bolt-down wheel guides
Steel tube or channel guides fixed with resin anchors into an existing concrete apron, typically galvanised or painted in high-visibility colours for drivers using mirrors.
What do the rules in England mean for the work?
Workplace safety in England is regulated by HSE. For a loading bay in Leatherhead, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about dock lights and wheel guides in Leatherhead
How do you price dock lights and wheel guides for a site in Leatherhead?
Guide budgets for supply and fit are £280 to £950 per item, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Do you cover Leatherhead for dock lights and wheel guides?
Yes. We take on dock lights and wheel guides for businesses in Leatherhead and across Surrey. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
What details do you need from us to quote for dock lights and wheel guides?
To get started, send the site address in Leatherhead, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Can dock lights be fitted without stopping loading?
Usually yes. Dock lights are fitted from inside the building beside the door, and the bay can often keep working except for a short period while the supply is isolated and connected. We agree timings with you so the work fits around trailer arrivals.
Can wheel guides be fitted to a tarmac yard?
Wheel guides can be fitted to a tarmac yard, but tarmac is usually too soft to hold anchors on its own. The normal approach is to cut out a strip and lay a concrete base for the guides. That work is identified at survey and included in the written quote.
Dock lights and wheel guides near Leatherhead
We also cover towns near Leatherhead, including Epsom (4 miles), Dorking (4 miles) and Esher (5 miles). Each has its own page with the same services and process.
Other loading bay services in Leatherhead
Full guide to dock lights and wheel guides · Everything we do in Leatherhead
Whether it is a new bay or a fault on an existing one, call us or request a quote for your site in Leatherhead.