- Location
- Egham, Surrey
- Main postcode district
- TW20
- Nearby (straight line)
- Staines (2 miles), Ashford (4 miles) and Windsor (4 miles)
- Visit pricing
- Agreed in writing before we attend
Dock leveller repair covers finding and fixing faults on the bridge between the dock and the trailer bed, including hydraulic cylinders, hoses and power packs, safety and check valves, lip hinges and lip cylinders, platform and lip damage, toe guards and control panels. It applies to swing-lip, telescopic-lip, mechanical and edge-of-dock levellers, with the aim of returning each one to safe working order.
Why do sites in Egham choose this?
When a leveller at a warehouse near Egham sinks under load, it should be taken out of use until the hydraulic cause has been found and fixed. Low temperatures at chilled and frozen docks in Egham can affect hydraulic oil and seals, so it helps to mention the operating temperature when reporting a fault.
Older units in Egham may still run mechanical or early hydraulic levellers, where a well-judged repair can keep the bay working before replacement is needed.
We do not turn up and then name a price. Every repair or service visit in Egham is agreed in writing first, including what the charge covers. Sending photos of the damage, error codes or leaks helps us diagnose the problem before travelling and bring the likely parts. Any additional work found on the day is quoted for your approval before it starts. You then get a written report for your records.
What are the most common dock leveller faults?
The most common dock leveller faults are hydraulic leaks, power pack failures, lip and hinge damage, and control faults. The way the leveller behaves usually points to the cause.
- Will not rise, or rises slowly: power pack motor or pump, low oil, a failed contactor or a control fault.
- Sinks under load or drifts down when parked: leaking cylinder seals or a faulty check valve.
- Drops suddenly, then locks: the safety valve doing its job after a hose or fitting failure.
- Lip will not extend or falls short: a lip cylinder fault, a sequence valve problem or a seized lip hinge.
- Oil in the pit: a leaking hose, fitting or cylinder.
- Jerky or noisy movement: air in the hydraulics or worn pivots.
- Cracked deck, bent lip or broken hinge knuckles: impact damage or fatigue.
A leveller showing any of these faults should be taken out of use until it has been checked.
What inspection rules apply to dock levellers?
Dock levellers are work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so they must be maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999.
Engineering insurers commonly inspect dock levellers under PUWER at 12-month intervals. Their reports list defects, sometimes marked for action before further use, and repairs are often needed to clear them.
Most levellers are treated as work equipment under PUWER. A leveller designed or used to lift people may fall under the Lifting Operations and Lifting Equipment Regulations (LOLER), with 6-monthly thorough examination. This depends on the equipment and how it is used; your insurer or competent person will confirm.
Levellers are made to BS EN 1398:2009, the dock leveller safety standard. HSE guidance notes that guards or skirting may be needed where something could be caught, so damaged toe guards are repaired as part of the job. See our guide to dock leveller inspections under PUWER and LOLER.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What else does the engineer check at the bay?
- Traffic light function and interlock operation
- Wiring, isolators and motor performance under load
- Door springs, cables and drums for wear or damage
- Track alignment, rollers and wall fixings
- Dock bumpers for missing rubber or loose fixings
- Door panels, side seals and bottom rubbers
Options to discuss
Power pack repairs
Motor, pump, valve block and contactor faults diagnosed and repaired, or the whole power pack replaced as a unit where that is the more economical option.
Control and safety repairs
Control panels, push buttons, limit switches, maintenance struts, toe guards and side skirts repaired or replaced so the leveller operates and parks safely.
Regulations and approvals in England
Workplace safety in England is regulated by HSE. For a loading bay in Egham, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies before any work starts and design the bay accordingly.
Questions about dock leveller repairs in Egham
How is a repair or service visit in Egham priced?
Repair and service visits are chargeable, and the price is agreed in writing before anyone attends. For dock leveller repairs, the guide budget is £220 to £2,600 per repair, excluding VAT. The exact figure depends on the fault, parts, access and timing. If the engineer finds further work on the day, it is quoted for your approval before it is carried out.
Do you cover Surrey for dock leveller repairs?
Yes. We take on dock leveller repairs for sites in Egham and throughout Surrey. Each visit is arranged in advance, with the price agreed in writing before anyone attends. Specialist service engineers working under our management carry out the work, and we remain your point of contact from the first call to the written report.
Can you take over our existing loading bay maintenance arrangement?
Yes. Send us a list of the equipment at your Egham site, with makes, models and approximate ages if known, plus recent service or inspection reports. We will propose a planned maintenance schedule and price it per item per visit. The first visit records the condition of everything, so you have a clear starting point for future servicing.
Can a leveller be repaired without disturbing the pit?
Usually yes. Most leveller repairs are carried out in place, working from the deck or from the pit with the platform propped. If the pit itself is cracked, broken at the edges or holding water, that is noted in the report and any pit repair is priced separately.
Can leveller repairs be done outside operating hours?
Yes, leveller repairs can be arranged for evenings or weekends where that suits your operation. Out-of-hours working costs more, and that is included in the visit price agreed in writing beforehand. Timing for each repair is agreed with you, and neighbouring bays can usually keep working.
Dock leveller repairs near Egham
If your site is not in Egham itself, it may be near one of these: Staines (2 miles), Ashford (4 miles) and Windsor (4 miles). Pick the closest.
Other loading bay services in Egham
Full guide to dock leveller repairs · Everything we do in Egham
Tell us what is happening at your Egham dock, what equipment is there and when it is used, and we will suggest the right next step.