- Location
- Long Eaton, Derbyshire
- Main postcode district
- NG10
- Nearby (straight line)
- Castle Donington (5 miles), Ilkeston (5 miles) and Nottingham (6 miles)
- Survey and quote
- Free, with a fixed written quote
Dock bumpers are rubber or rubber-and-steel buffers fixed to the face of a loading dock, either side of the leveller, to absorb the impact of reversing vehicles. They hold the trailer a set distance from the building, protect the dock wall, leveller and door, and help a dock seal or shelter compress evenly. Most bays use two bumpers, replaced as they wear.
Why do sites in Long Eaton choose this?
For new-build warehouses in Long Eaton, bumpers are best specified alongside the leveller and seal so that projection and seal compression are correct before the first trailer arrives. Sites near Long Eaton handling a mix of articulated trailers, rigid vehicles and vans may need taller bumpers or a second lower pair to protect the dock face.
Distribution sheds in Long Eaton that take trailers on and off the dock all day wear through bumper rubber faster than quieter sites, so it pays to check them at every service.
Keeping the dock running is usually the first concern, so we plan around it. After a free survey of your Long Eaton site and a written quote at a fixed price, we agree when each bay can be released and whether any work should happen out of hours. Specialist installation engineers working under our management then fit the equipment, and we test it and hand over the documentation before the bay goes back into use.
How much do dock bumpers cost?
Dock bumpers typically cost £120 to £480 per bumper, supplied and fitted, excluding VAT. Most bays need two, so the cost per dock depends mainly on the type of bumper and how it is fixed.
The main things that move the price are:
- Bumper type: laminated rubber is the most economical; moulded, steel-faced and vertical sliding designs cost more.
- Size and projection: deeper or taller bumpers use more material and heavier fixings.
- Fixing method: anchoring into sound concrete is simpler than welding to steel embeds or repairing a broken dock face first.
- Number of bays: doing several docks in one visit spreads access and travel costs.
- Working hours and location: out-of-hours working and remote or island sites add cost, and any travel cost is shown in the quote.
These are guide budgets. After a free site survey we send a written quote, and that quote is the fixed price. VAT is added at the standard rate.
Which dock bumper is best: laminated, moulded or steel-faced?
Laminated rubber bumpers suit most general docks, steel-faced bumpers suit busy bays where trailers rise and fall during loading, and moulded bumpers suit lighter vehicles and compact installations.
- Laminated rubber: layers of fabric-reinforced rubber pressed between steel angles on threaded bars. They absorb impact well, are economical and are the standard choice for many bays.
- Moulded rubber: solid rubber blocks in rectangular or curved profiles. They are neat and quick to fit, and work well for vans, rigid vehicles and lower-impact docks.
- Steel-faced: a rubber body behind a steel plate. As forklifts drive on and off, the trailer bed moves up and down and scrubs the bumper; the steel face takes that wear instead of the rubber.
- Vertical sliding: a face that travels up and down with the trailer, reducing abrasion on very busy bays.
Where a design has replaceable faces, worn plates can be changed without removing the whole bumper. Our guide to choosing dock bumpers and wheel guides covers projection and positioning in more detail.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- How drivers are prevented from pulling away too early
- Age and condition of the equipment already in place
- Access for deliveries, cranes or lifting equipment during installation
- Asbestos register and any other site hazard information
- Condition of any existing leveller pit, kerb angles and pit drainage
- Dock height and the mix of trailers you load
Options to discuss
Replacement faces and fixings
New face plates, rubber inserts and anchors for existing bumpers where the body and backing are still sound, keeping replacement costs down on worn bays.
Steel-faced bumpers
A rubber body behind a steel face plate that resists scuffing as the trailer bed moves during loading. Suited to busy bays with heavy forklift traffic.
Planning, building control and safety law in England
Sites in Long Eaton fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.
Questions about dock bumpers in Long Eaton
Do you cover Long Eaton for dock bumpers?
Yes. We take on dock bumpers for businesses in Long Eaton and across Derbyshire. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Long Eaton site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Long Eaton, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Can you replace just the face of a dock bumper?
Yes, on bumpers designed with replaceable faces. Steel-faced and some moulded designs let the worn face plate or rubber insert be changed while the backing stays bolted to the dock. Older laminated bumpers usually have to be replaced as a complete unit, which is still a modest cost compared with repairing impact damage to a leveller.
Can dock bumpers be fitted with an edge-of-dock leveller?
Yes. With an edge-of-dock leveller, bumpers are usually fixed to the dock face either side of the unit, or to the leveller's own mounting frame where it is designed for that. Their projection has to suit the short lip so it still reaches on to the trailer bed, which we check at survey.
Dock bumpers near Long Eaton
Sites close to Long Eaton get the same service, including those in Castle Donington (5 miles), Ilkeston (5 miles) and Nottingham (6 miles), with every job run the same way.
Other loading bay services in Long Eaton
Full guide to dock bumpers · Everything we do in Long Eaton
Use the quote tool to tell us about the doors, levellers or shelters at your Long Eaton site, and we will be in touch to arrange the next step.