- Location
- Long Eaton, Derbyshire
- Main postcode district
- NG10
- Nearby (straight line)
- Castle Donington (5 miles), Ilkeston (5 miles) and Nottingham (6 miles)
- Survey and quote
- Free, with a fixed written quote
A retractable dock shelter is a fabric shelter fixed to the building around a loading bay door, with flexible top and side curtains carried on a sprung or pantograph steel frame. When a trailer reverses in, the frame retracts and the curtains drape against the trailer's sides and roof, closing most of the gap while leaving the full width of the trailer opening clear for loading.
Why do sites in Long Eaton choose this?
Retail and e-commerce distribution centres in Long Eaton with high trailer turnover need tough sprung-frame shelters that recover quickly after each departure. Shelter sizing for a bay in Long Eaton starts with measuring the door and wall and recording the tallest, lowest and widest trailers you receive.
Third-party logistics sites in Long Eaton receiving trailers from many hauliers usually need a shelter rather than a seal, because widths and heights vary.
The survey is free, the quote is written and the price is fixed: that is how every installation in Long Eaton begins. We then manage the work from start to finish. Fitting is carried out by specialist installers under our management, phased so the operation keeps moving, and nights or weekends can be booked by arrangement. On the final day we test the equipment with you and hand over the operating and maintenance information.
Why do trailer door hinges matter when choosing a shelter?
Trailer door hinges matter because the rear doors are opened and folded back along the trailer sides before reversing, and the shelter has to accommodate them. If the shelter is too shallow, the hinges and doors sit outside it, leaving gaps or snagging the curtains.
A shelter handles this better than a seal:
- its side curtains drape over the opened doors and hinges rather than pressing against them,
- the full width of the trailer opening stays clear, because nothing protrudes in front of the trailer's rear frame,
- slit curtains wrap around hinge blocks without tearing.
By contrast, a dock seal presses against the rear of the trailer, so gaps at the hinges can remain, and poorly sized side pads can intrude into the opening. That is why shelters are generally favoured for mixed fleets, where hinge positions and trailer widths vary from one vehicle to the next.
How do I size a retractable shelter for my trailers?
Size a retractable shelter to the largest trailer you receive, with a projection deep enough for opened trailer doors and the leveller lip, and curtains that still reach the smallest vehicles. The trailer mix sets almost every dimension.
- Width: wider than the trailer, so the side curtains drape along its sides rather than across the opening.
- Height: high enough for the tallest trailers, with a top curtain deep enough to reach the roof of the lowest.
- Projection: deep enough for the rear doors, folded back along the trailer sides, to sit inside the curtains.
- Curtain cut-outs: vertical slits let the side curtains wrap around hinges and rear fittings without tearing.
- Guide stripes: contrasting stripes on the curtains help drivers centre the trailer.
If your fleet is uniform, a seal may give a tighter fit. Our guide to shelters and seals sets out the trade-offs.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Control positions, isolators and any existing interlocks
- Whether planning, building control or a building warrant may be needed
- Bumper position and wear or damage on the dock face
- Access for deliveries, cranes or lifting equipment during installation
- Traffic routes for vehicles and separation of pedestrians
- Dock height and the mix of trailers you load
Options to discuss
Rigid frame with long curtains
A fixed frame carrying long flexible curtains, useful where the trailer only needs to touch the curtains and the frame can stay clear of impact.
Guide stripes
Contrasting high-visibility stripes on the curtains that give drivers a clear target to aim for when reversing onto the bay.
Regulations and approvals in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Long Eaton. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about retractable dock shelters in Long Eaton
How long does installation take at a site in Long Eaton?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
What details do you need from us to quote for retractable dock shelters?
To get started, send the site address in Long Eaton, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Will you deal with building control and planning for a project in Long Eaton?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
What projection should a dock shelter have?
Projection should be deep enough to clear opened trailer doors and hinges and to suit the leveller lip and bumpers. Shelters are commonly made with projections from around 500 to 1,000 mm, and we recommend a depth once we know your trailers and leveller.
Can a shelter be fixed to a cladded wall?
Yes, but cladding on its own is not usually strong enough to carry a shelter. We fix through to the building's steel frame behind the cladding, or use a steel subframe or spreader plates to spread the load, and confirm the method after inspecting the wall.
Retractable dock shelters near Long Eaton
Sites close to Long Eaton get the same service, including those in Castle Donington (5 miles), Ilkeston (5 miles) and Nottingham (6 miles), with every job run the same way.
Other loading bay services in Long Eaton
Full guide to retractable dock shelters · Everything we do in Long Eaton
Request a quote for your loading bay in Long Eaton, attaching photos of the dock, the equipment and any damage.