- Location
- Stevenage, Hertfordshire
- Main postcode district
- SG1
- Nearby (straight line)
- Hitchin (5 miles), Letchworth Garden City (5 miles) and Welwyn Garden City (7 miles)
- Survey and quote
- Free, with a fixed written quote
A vehicle restraint is a device at a loading bay that physically holds a trailer against the dock until it is safe to leave. In the UK most systems act on the rear wheel, either as a powered wheel-based restraint or a sensor wheel chock. Restraints guard against early drive-away and trailer creep, and are usually interlocked with the door and dock traffic lights.
Where does this fit at a dock in Stevenage?
New-build distribution sheds in Stevenage can have restraint rails and ducting planned into the yard slab from the start, which is simpler than cutting them in later. Operators in Stevenage reviewing their workplace transport risk assessment often look at restraints when key control alone has proved hard to enforce across shifts.
Yards around Stevenage that park uncoupled trailers at the dock can see trailers creep under forklift traffic, and a wheel-based restraint helps keep the leveller lip on the bed.
A single contact at Loading Bay Doors handles your project in Stevenage from start to finish. The free site survey and fixed written quote come first, with no obligation to proceed. We then book the installation for times that suit the operation, including out of hours by arrangement, and manage the specialist engineers on site. At the end we commission and test the equipment, walk your team through it and provide the documentation.
What does HSE guidance say about preventing drive-away?
HSE guidance says there must be safeguards to stop drivers driving away from a loading bay too early, and it lists vehicle or trailer restraints as one of the measures. The others it names are traffic lights and the person in charge keeping the vehicle keys or paperwork until it is safe to leave.
This comes from HSE's guide to workplace transport safety (HSG136) and its loading and unloading factsheet. The guidance sets out the outcome rather than one fixed solution, so the right combination for your site should follow your own risk assessment.
Once fitted, a restraint is work equipment under the Provision and Use of Work Equipment Regulations 1998 (PUWER), so it must be suitable, maintained in a safe condition and inspected where deterioration could lead to danger. In Northern Ireland the equivalent is PUWER (Northern Ireland) 1999, and the regulator is HSENI rather than HSE.
Our guide to preventing drive-away and trailer creep compares the options side by side.
Wheel-based or hook restraint: which suits UK trailers?
Wheel-based restraints and sensor wheel chocks suit most UK trailers, because they act on the rear wheel rather than on the back of the vehicle. Hook restraints, which catch the rear impact guard (sometimes called an ICC bar), are common elsewhere but suit fewer UK fleets.
- Wheel-based restraint: a steel guide rail fixed to the yard, with an arm or chock that moves against the rear wheel, either powered or pushed into place by the operative. It works regardless of tail lifts or underrun guard design.
- Sensor wheel chock: a heavy chock placed in front of the wheel, with a sensor or parking station that tells the dock controls it is in position. Lower cost and minimal groundwork, but it relies on someone placing it each time.
- Hook restraint: mounted on the dock face and hooking the rear guard. UK and European trailers vary widely at the rear, and tail lifts often get in the way, so this type needs checking against your actual fleet.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Dock height and the mix of trailers you load
- Bumper position and wear or damage on the dock face
- Working hours, shift patterns and windows for out-of-hours work
- Wall and steel structure for door, shelter and bumper fixings
- Escape routes and pedestrian doors close to the bay
- How drivers are prevented from pulling away too early
Options to discuss
Hook restraint
A dock-mounted hook that catches the trailer's rear impact guard. Only suitable where your fleet has compatible rear guards, which we check carefully at survey.
Automatic wheel-based restraint
A powered arm on a yard-mounted rail that locates against the rear wheel at the push of a button and signals the dock controls once the trailer is held.
Planning, building control and safety law in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Stevenage. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about vehicle restraints in Stevenage
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Stevenage, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
How long does installation take at a site in Stevenage?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Can you work alongside our main contractor on a new build in Stevenage?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Do vehicle restraints work with all trailers?
Wheel-based restraints and sensor chocks work with most trailers, because they act on the rear wheel rather than on the back of the vehicle. Vehicles with unusual wheel positions or very small wheels need checking, so we look at the vehicles you receive during the survey.
What happens if a powered restraint loses power?
Powered restraints are normally designed with a manual release so a trailer is not trapped on the bay if power is lost. Your site procedure should say who is allowed to use the release and what checks they make first. We explain the release method at handover.
Vehicle restraints near Stevenage
Looking beyond Stevenage? Our pages for Hitchin (5 miles), Letchworth Garden City (5 miles) and Welwyn Garden City (7 miles) describe the same loading bay services and how to get in touch.
Other loading bay services in Stevenage
Full guide to vehicle restraints · Everything we do in Stevenage
Speak to us about your Stevenage loading bay. We will ask the right questions, then set out the next step clearly.