- Location
- Stroud, Gloucestershire
- Main postcode district
- GL5
- Nearby (straight line)
- Gloucester (8 miles), Cirencester (10 miles) and Cheltenham (12 miles)
- Survey and quote
- Free, with a fixed written quote
A vehicle restraint is a device at a loading bay that physically holds a trailer against the dock until it is safe to leave. In the UK most systems act on the rear wheel, either as a powered wheel-based restraint or a sensor wheel chock. Restraints guard against early drive-away and trailer creep, and are usually interlocked with the door and dock traffic lights.
What should sites in Stroud consider?
New-build distribution sheds in Stroud can have restraint rails and ducting planned into the yard slab from the start, which is simpler than cutting them in later. Third-party hauliers visiting sites in Stroud may not know each site's procedures, so a restraint that holds the wheel removes reliance on every driver following instructions.
Restraint systems for sites in Stroud are surveyed, quoted and installed in the same way as anywhere else in the UK, with a fixed price set out in writing.
The survey is free, the quote is written and the price is fixed: that is how every installation in Stroud begins. We then manage the work from start to finish. Fitting is carried out by specialist installers under our management, phased so the operation keeps moving, and nights or weekends can be booked by arrangement. On the final day we test the equipment with you and hand over the operating and maintenance information.
What is trailer creep and how does a restraint stop it?
Trailer creep is the gradual movement of a parked trailer away from the dock, caused by forklifts braking and accelerating as they drive on and off the trailer bed. Each movement pushes the trailer forward slightly, and over a full load the gap can grow.
Creep is more likely when:
- the trailer is uncoupled from its tractor unit and resting on its landing legs;
- air suspension or brakes have not been set correctly by the driver;
- forklifts are heavy, fast or carrying dense loads such as drinks or building materials;
- the yard falls slightly away from the building.
As the trailer moves, the leveller lip can lose its bearing on the trailer bed, and in the worst case the lip slips off with a forklift on it. A wheel-based restraint holds the wheel against the rail or chock, so the trailer cannot travel forward however many times a forklift drives on and off.
What happens on site when a vehicle restraint is installed?
Installing a vehicle restraint takes the bay out of use while the rail or chock station is fixed, cabled and tested, but neighbouring bays can usually keep working.
- Set out: the restraint position is marked in line with the bay so it meets the rear wheels of the trailers you receive.
- Fixing: rail-mounted units are anchored into the concrete apron. If a new concrete base is needed, it must cure before the restraint is fitted.
- Cabling: ducts are cut or laid from the restraint to the dock wall, and the control box is fitted inside next to the door.
- Connection: the restraint is wired into the door, leveller and traffic light controls so the sequence works as designed.
- Commissioning: the system is tested with a trailer on the bay, and dock staff are shown how to engage and release it.
We ask you to release the bay for the agreed period, confirm an electrical supply point, provide a trailer for commissioning and tell us about any buried services in the yard.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Control positions, isolators and any existing interlocks
- Traffic routes for vehicles and separation of pedestrians
- Scope to convert ground-level doors into docks or add lift tables
- Whether planning, building control or a building warrant may be needed
- Power supply at each bay, including three-phase availability
- Lighting inside trailers and at the dock face
Options to discuss
Hook restraint
A dock-mounted hook that catches the trailer's rear impact guard. Only suitable where your fleet has compatible rear guards, which we check carefully at survey.
Automatic wheel-based restraint
A powered arm on a yard-mounted rail that locates against the rear wheel at the push of a button and signals the dock controls once the trailer is held.
Regulations and approvals in England
Workplace safety in England is regulated by HSE. For a loading bay in Stroud, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about vehicle restraints in Stroud
Is VAT included in your guide prices for vehicle restraints?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Gloucestershire as everywhere else: for vehicle restraints, it is £4,200 to £9,800 per bay, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
How long does installation take at a site in Stroud?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Stroud site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Can a vehicle restraint be fitted to an existing bay?
Yes, restraints are commonly retrofitted to existing bays. The main questions are whether the yard concrete in front of the bay is sound enough to anchor a rail, how cables will reach the dock controls, and whether the existing door and leveller panels can accept interlocks. Sensor chocks are often chosen where groundwork needs to be kept to a minimum.
Do vehicle restraints work with all trailers?
Wheel-based restraints and sensor chocks work with most trailers, because they act on the rear wheel rather than on the back of the vehicle. Vehicles with unusual wheel positions or very small wheels need checking, so we look at the vehicles you receive during the survey.
Vehicle restraints near Stroud
Businesses outside Stroud may find their nearest town in this list: Gloucester (8 miles), Cirencester (10 miles) and Cheltenham (12 miles). Each page covers doors, docks, repairs and servicing.
Other loading bay services in Stroud
Full guide to vehicle restraints · Everything we do in Stroud
Request a quote for your loading bay in Stroud, attaching photos of the dock, the equipment and any damage.