- Location
- Kendal, Cumbria
- Main postcode district
- LA9
- Nearby (straight line)
- Morecambe (18 miles), Lancaster (19 miles) and Heysham (20 miles)
- Survey and quote
- Free, with a fixed written quote
A vehicle restraint is a device at a loading bay that physically holds a trailer against the dock until it is safe to leave. In the UK most systems act on the rear wheel, either as a powered wheel-based restraint or a sensor wheel chock. Restraints guard against early drive-away and trailer creep, and are usually interlocked with the door and dock traffic lights.
What should sites in Kendal consider?
Yards around Kendal that park uncoupled trailers at the dock can see trailers creep under forklift traffic, and a wheel-based restraint helps keep the leveller lip on the bed. A warehouse in Kendal that already uses traffic lights may want to add restraints so the door cannot open until the trailer is physically held in place.
Operators in Kendal reviewing their workplace transport risk assessment often look at restraints when key control alone has proved hard to enforce across shifts.
Here is what happens after you contact us about a site in Kendal. We arrange a free survey, measure up and send a fixed written quote. If you go ahead, we manage the whole job, including ordering, delivery and coordination with your site team. Specialist installation engineers working under our management do the fitting, at times built around your loading schedule, with out-of-hours work by arrangement. Testing and handover documents close the job.
How much does a vehicle restraint cost?
A vehicle restraint typically costs £4,200 to £9,800 per bay, supplied and installed, excluding VAT. Sensor wheel chocks linked to the dock controls usually sit towards the lower end, and fully automatic wheel-based restraints with rail and interlocks towards the upper end.
What moves the price:
- Restraint type: a sensor chock needs far less hardware and groundwork than a powered, rail-mounted wheel restraint.
- Yard condition: rail-mounted units need a sound, level concrete apron. Broken concrete or tarmac may need a new base, priced after survey.
- Cabling: the distance from the restraint to the dock control panel, and whether ducts must be cut into the yard.
- Integration: linking to existing door and leveller controls is simpler on modern panels; older panels may need replacing.
- Number of bays and working hours: several bays in one project spread set-up costs, while out-of-hours work adds cost.
All figures are guide budgets. After a free site survey we send a written quote, and that quote is the fixed price. VAT is added at the standard rate.
Wheel-based or hook restraint: which suits UK trailers?
Wheel-based restraints and sensor wheel chocks suit most UK trailers, because they act on the rear wheel rather than on the back of the vehicle. Hook restraints, which catch the rear impact guard (sometimes called an ICC bar), are common elsewhere but suit fewer UK fleets.
- Wheel-based restraint: a steel guide rail fixed to the yard, with an arm or chock that moves against the rear wheel, either powered or pushed into place by the operative. It works regardless of tail lifts or underrun guard design.
- Sensor wheel chock: a heavy chock placed in front of the wheel, with a sensor or parking station that tells the dock controls it is in position. Lower cost and minimal groundwork, but it relies on someone placing it each time.
- Hook restraint: mounted on the dock face and hooking the rear guard. UK and European trailers vary widely at the rear, and tail lifts often get in the way, so this type needs checking against your actual fleet.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Dock height and the mix of trailers you load
- Condition of any existing leveller pit, kerb angles and pit drainage
- Power supply at each bay, including three-phase availability
- How drivers are prevented from pulling away too early
- Clear opening width and height for each door
- Wind exposure at the dock, which affects door and shelter choice
Options to discuss
Sensor wheel chock
A heavy-duty chock with a sensor or parking station that tells the dock controls when it is in place. Minimal groundwork and suited to retrofit on existing bays.
Automatic wheel-based restraint
A powered arm on a yard-mounted rail that locates against the rear wheel at the push of a button and signals the dock controls once the trailer is held.
Regulations and approvals in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Kendal. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about vehicle restraints in Kendal
Will you deal with building control and planning for a project in Kendal?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
What details do you need from us to quote for vehicle restraints?
To get started, send the site address in Kendal, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Do you remove and dispose of the old equipment?
Yes, where it is part of the scope. When we replace doors, levellers, shelters or seals at a site in Kendal, removal and disposal of the old equipment can be included and is itemised in the quote, so it is clear what is covered. If anything should be kept, such as a frame or motor that is still serviceable, we agree that at survey.
Do vehicle restraints need servicing?
Yes. A restraint is work equipment under PUWER, so it must be maintained in a safe condition and inspected where wear could lead to danger. Servicing typically covers the rail and arm, sensors, controls and the interlock sequence with the door and lights.
Is a vehicle restraint a legal requirement?
Not in every case: HSE guidance (followed by HSENI in Northern Ireland) says there should be safeguards against drivers driving away too early, and a vehicle restraint is one of the measures it lists. Traffic lights and the person in charge keeping keys or paperwork are the others. Which measures you use should follow your risk assessment. In Northern Ireland the regulator is HSENI.
Vehicle restraints near Kendal
Other towns within reach of Kendal on our coverage list include Morecambe (18 miles), Lancaster (19 miles) and Heysham (20 miles), all covered on the same terms.
Other loading bay services in Kendal
Full guide to vehicle restraints · Everything we do in Kendal
Speak to us about your Kendal loading bay. We will ask the right questions, then set out the next step clearly.