A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
How does this suit sites in the Highlands?
Cold chain operators around the Highlands loading refrigerated trailers right to the doors may find a telescopic lip makes the last pallets far easier to handle. Parcel and courier hubs in the Highlands with varied vehicle types can use the longer lip reach to serve more of their fleet from fewer bays.
Manufacturing sites in the Highlands that end-load finished goods can place the lip precisely between pallets to reach the rear row.
Before anything is ordered, we visit your site in the Highlands for a free survey and then send a written quote with a fixed price. From that point we manage the installation, coordinating delivery, access and any other trades. Fitting is done by specialist installation engineers engaged and managed by us, at times that suit your operation, including out of hours where agreed. You get a tested installation, a demonstration for your team and the manufacturer documentation.
Can a telescopic leveller replace a swing-lip unit in the same pit?
Often yes, a telescopic-lip leveller can replace a swing-lip unit in the same pit, provided the pit is square and deep enough and the edge steel is in good condition. Some telescopic units need a little more depth for the lip mechanism, so we measure carefully at survey.
A typical installation:
- The bay is closed and the old leveller isolated, lifted out and removed.
- The pit is cleaned and measured, and any edge steel repairs carried out.
- The new unit is set in, levelled and fixed to the pit steel.
- The power pack, control panel and lip controls are connected and interlocks wired.
- The platform and lip are tested through their full travel.
You will need to provide a clear bay, access for lifting equipment and a suitable power supply, typically three-phase. Installation commonly takes one to two working days per bay once the pit is ready.
How far should a telescopic lip extend?
A telescopic lip should extend far enough to reach clear bed space on every trailer you load, including over tail lifts, while still leaving a secure overlap on the bed. Telescopic lips commonly extend 500 to 1,000 mm.
- Around 500 mm: suits fleets without tail lifts that need precise placement and end loading.
- Up to around 1,000 mm: reaches over folded tail lifts and across the larger gap left where deep bumpers hold trailers back from the dock edge.
- Platform length: should match the lip, as a long reach on a short platform can leave steep gradients.
- Lip width: full-width lips suit most work, while narrower or tapered lips help with smaller vehicles.
We record the rear details of the trailers you receive, including tail lift depth and bumper projection, then recommend the shortest extension that covers them all. A longer lip than you need adds cost and weight without benefit.
Towns we cover in the Highlands
Find your town in the list below for details of telescopic-lip dock levellers across the Highlands, or contact us if your location is not shown.
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
Which rules apply in Scotland?
Doors and dock equipment installed in Scotland may carry the UKCA or the CE mark, and we pass on the documentation for everything fitted in the Highlands. Because building warrant and planning questions can affect the programme, we check what applies at survey and raise any approvals early rather than assuming none are needed.
Questions
Is the site survey in the Highlands free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Is VAT included in your guide prices for telescopic-lip dock levellers?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in the Highlands as everywhere else: for telescopic-lip dock levellers, it is £6,800 to £11,800 per leveller, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Do telescopic levellers need more maintenance?
They have more moving parts than a swing-lip leveller, including the lip guides and lip cylinder, so these need checking and lubricating at each service. With planned servicing the extra work is modest. Servicing is chargeable, with the visit price agreed in advance.
Are telescopic levellers suitable for cold stores?
Yes, telescopic levellers are widely used in cold stores because refrigerated trailers are often loaded right to the rear doors. Insulated platforms and perimeter seals reduce cold loss through the pit, and the leveller is usually interlocked with the door and shelter.
Other services in the Highlands
Full guide to telescopic-lip dock levellers · All loading bay services in the Highlands