- Location
- Rottingdean, East Sussex
- Main postcode district
- BN2
- Nearby (straight line)
- Peacehaven (3 miles), Brighton (4 miles) and Hove (5 miles)
- Survey and quote
- Free, with a fixed written quote
A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
Why do sites in Rottingdean choose this?
Replacing worn swing-lip levellers at a site in Rottingdean is a good moment to ask whether the current trailer mix now calls for telescopic lips. A container-handling operation in Rottingdean can benefit from a telescopic lip, as container floors and chassis heights vary more than standard trailers.
Where docks in Rottingdean have deep bumpers that hold trailers away from the edge, a telescopic lip can bridge a gap a swing lip would struggle to cover.
Here is what happens after you contact us about a site in Rottingdean. We arrange a free survey, measure up and send a fixed written quote. If you go ahead, we manage the whole job, including ordering, delivery and coordination with your site team. Specialist installation engineers working under our management do the fitting, at times built around your loading schedule, with out-of-hours work by arrangement. Testing and handover documents close the job.
Can a telescopic leveller replace a swing-lip unit in the same pit?
Often yes, a telescopic-lip leveller can replace a swing-lip unit in the same pit, provided the pit is square and deep enough and the edge steel is in good condition. Some telescopic units need a little more depth for the lip mechanism, so we measure carefully at survey.
A typical installation:
- The bay is closed and the old leveller isolated, lifted out and removed.
- The pit is cleaned and measured, and any edge steel repairs carried out.
- The new unit is set in, levelled and fixed to the pit steel.
- The power pack, control panel and lip controls are connected and interlocks wired.
- The platform and lip are tested through their full travel.
You will need to provide a clear bay, access for lifting equipment and a suitable power supply, typically three-phase. Installation commonly takes one to two working days per bay once the pit is ready.
How far should a telescopic lip extend?
A telescopic lip should extend far enough to reach clear bed space on every trailer you load, including over tail lifts, while still leaving a secure overlap on the bed. Telescopic lips commonly extend 500 to 1,000 mm.
- Around 500 mm: suits fleets without tail lifts that need precise placement and end loading.
- Up to around 1,000 mm: reaches over folded tail lifts and across the larger gap left where deep bumpers hold trailers back from the dock edge.
- Platform length: should match the lip, as a long reach on a short platform can leave steep gradients.
- Lip width: full-width lips suit most work, while narrower or tapered lips help with smaller vehicles.
We record the rear details of the trailers you receive, including tail lift depth and bumper projection, then recommend the shortest extension that covers them all. A longer lip than you need adds cost and weight without benefit.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- How drivers are prevented from pulling away too early
- How often each door cycles during a typical shift
- Wheel guide positions and yard markings for reversing vehicles
- Bumper position and wear or damage on the dock face
- Access for deliveries, cranes or lifting equipment during installation
- Escape routes and pedestrian doors close to the bay
Options to discuss
Automatic return control
A single button that withdraws the lip and lowers the platform to its stored position, reducing the risk of a trailer leaving with the lip still out.
500 mm lip extension
A commonly specified reach for precise placement and end loading on standard trailers and refrigerated vehicles that do not have tail lifts.
Regulations and approvals in England
Workplace safety in England is regulated by HSE. For a loading bay in Rottingdean, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about telescopic-lip dock levellers in Rottingdean
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Rottingdean site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Is the site survey in Rottingdean free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Is VAT included in your guide prices for telescopic-lip dock levellers?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in East Sussex as everywhere else: for telescopic-lip dock levellers, it is £6,800 to £11,800 per leveller, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
What overlap should the lip have on the trailer bed?
The lip should rest on the trailer bed with the overlap the manufacturer specifies, so it cannot slip off as the trailer moves under load. Extending further than needed adds no benefit. We show dock staff what a correct overlap looks like at handover.
Can telescopic and swing-lip levellers be mixed on one dock?
Yes, and many sites do. Fitting telescopic levellers on the bays that receive tail-lift vehicles or need end loading, and swing-lip units on the rest, keeps costs down while covering every vehicle type. Clear bay signage helps drivers reverse onto the right one.
Telescopic-lip dock levellers near Rottingdean
Sites close to Rottingdean get the same service, including those in Peacehaven (3 miles), Brighton (4 miles) and Hove (5 miles), with every job run the same way.
Other loading bay services in Rottingdean
Full guide to telescopic-lip dock levellers · Everything we do in Rottingdean
Start your enquiry for Rottingdean through the quote tool. A few photos and approximate sizes help us respond with something useful.