- Location
- Portslade, East Sussex
- Main postcode district
- BN41
- Nearby (straight line)
- Hove (2 miles), Shoreham-by-Sea (3 miles) and Brighton (3 miles)
- Survey and quote
- Free, with a fixed written quote
A telescopic-lip dock leveller is a hydraulic pit leveller whose front lip slides forward out of the platform, rather than swinging on a hinge, and can be extended by a controlled amount onto the trailer bed. Telescopic lips commonly extend 500 to 1,000 mm, which lets operators reach over tail lifts, place the lip between pallets and load the last row in a trailer.
Where does this fit at a dock in Portslade?
Retail distribution sites in Portslade receiving both artics and tail-lift rigids at the same bays can handle the whole mix with a telescopic-lip leveller. Parcel and courier hubs in Portslade with varied vehicle types can use the longer lip reach to serve more of their fleet from fewer bays.
A container-handling operation in Portslade can benefit from a telescopic lip, as container floors and chassis heights vary more than standard trailers.
Our part of the job in Portslade is to survey, quote and manage; the fitting itself is done by specialist installation engineers working under our management. The survey and the written quote are free. Once the fixed price is accepted, we agree dates that work around your deliveries and shifts, including out-of-hours working where needed. Every installation is tested before handover, and you receive the documentation for each item fitted.
Can a telescopic leveller replace a swing-lip unit in the same pit?
Often yes, a telescopic-lip leveller can replace a swing-lip unit in the same pit, provided the pit is square and deep enough and the edge steel is in good condition. Some telescopic units need a little more depth for the lip mechanism, so we measure carefully at survey.
A typical installation:
- The bay is closed and the old leveller isolated, lifted out and removed.
- The pit is cleaned and measured, and any edge steel repairs carried out.
- The new unit is set in, levelled and fixed to the pit steel.
- The power pack, control panel and lip controls are connected and interlocks wired.
- The platform and lip are tested through their full travel.
You will need to provide a clear bay, access for lifting equipment and a suitable power supply, typically three-phase. Installation commonly takes one to two working days per bay once the pit is ready.
How far should a telescopic lip extend?
A telescopic lip should extend far enough to reach clear bed space on every trailer you load, including over tail lifts, while still leaving a secure overlap on the bed. Telescopic lips commonly extend 500 to 1,000 mm.
- Around 500 mm: suits fleets without tail lifts that need precise placement and end loading.
- Up to around 1,000 mm: reaches over folded tail lifts and across the larger gap left where deep bumpers hold trailers back from the dock edge.
- Platform length: should match the lip, as a long reach on a short platform can leave steep gradients.
- Lip width: full-width lips suit most work, while narrower or tapered lips help with smaller vehicles.
We record the rear details of the trailers you receive, including tail lift depth and bumper projection, then recommend the shortest extension that covers them all. A longer lip than you need adds cost and weight without benefit.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Wheel guide positions and yard markings for reversing vehicles
- Power supply at each bay, including three-phase availability
- How often each door cycles during a typical shift
- Condition of any existing leveller pit, kerb angles and pit drainage
- Traffic routes for vehicles and separation of pedestrians
- Whether planning, building control or a building warrant may be needed
Options to discuss
Insulated cold store version
An insulated platform with perimeter seals for chilled and frozen docks, often paired with an inflatable shelter and an insulated dock door.
Automatic return control
A single button that withdraws the lip and lowers the platform to its stored position, reducing the risk of a trailer leaving with the lip still out.
Planning, building control and safety law in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Portslade. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about telescopic-lip dock levellers in Portslade
How do you price telescopic-lip dock levellers for a site in Portslade?
Guide budgets for supply and fit are £6,800 to £11,800 per leveller, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Is VAT included in your guide prices for telescopic-lip dock levellers?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in East Sussex as everywhere else: for telescopic-lip dock levellers, it is £6,800 to £11,800 per leveller, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Do you cover Portslade for telescopic-lip dock levellers?
Yes. We take on telescopic-lip dock levellers for businesses in Portslade and across East Sussex. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
What overlap should the lip have on the trailer bed?
The lip should rest on the trailer bed with the overlap the manufacturer specifies, so it cannot slip off as the trailer moves under load. Extending further than needed adds no benefit. We show dock staff what a correct overlap looks like at handover.
Do telescopic levellers need more maintenance?
They have more moving parts than a swing-lip leveller, including the lip guides and lip cylinder, so these need checking and lubricating at each service. With planned servicing the extra work is modest. Servicing is chargeable, with the visit price agreed in advance.
Telescopic-lip dock levellers near Portslade
Sites close to Portslade get the same service, including those in Hove (2 miles), Shoreham-by-Sea (3 miles) and Brighton (3 miles), with every job run the same way.
Other loading bay services in Portslade
Full guide to telescopic-lip dock levellers · Everything we do in Portslade
Phone us to discuss your loading bay in Portslade, or start with the online quote tool if you prefer to send details first.