Swing-lip dock levellers in Witney

Location

Witney, Oxfordshire

Main postcode districts

OX28 and OX29

Nearby (straight line)

Carterton (5 miles), Oxford (10 miles) and Abingdon (12 miles)

Survey and quote

Free, with a fixed written quote

How does this suit sites in Witney?

Ageing levellers in older docks around Witney can often be replaced like for like in the existing pit, avoiding new concrete work if the pit is sound. Every leveller recommendation we make for a dock in Witney follows a measured survey of the pit, dock height and the trailers you actually receive.

Mixed bays at a site in Witney, where some trailers have tail lifts and others do not, may suit a combination of swing-lip and telescopic levellers.

We keep the process simple for sites in Witney. A free survey tells us what the dock needs; a fixed written quote tells you what it will cost and what is included. We then organise the installation, with specialist engineers under our management and a programme agreed around your shifts. Night and weekend work is available by arrangement. Before we leave, the new equipment is tested, demonstrated and handed over with its documentation.

How long should a dock leveller platform be?

A leveller platform should be long enough to keep the slope gentle across the full range of trailer heights you load, because the steepest gradient decides which handling equipment can use it safely. A longer platform spreads the same height difference over a greater distance.

• Know your trailer mix: with a dock typically around 1,200 mm high and trailer beds ranging from roughly 900 to 1,600 mm, the height difference can be considerable.
• Check your equipment: low-clearance electric pallet trucks cope with less gradient than a counterbalance forklift with good ground clearance.
• Common lengths: platforms are commonly made from around 2 to 3.5 m long, with longer units where trailers sit very low or very high.
• Width: a wider platform gives more room when pallets sit close to the trailer sides.

When replacing a unit, the pit size limits what can be fitted, so we measure the pit and record your trailer heights at survey before recommending a length.

What happens when a swing-lip leveller is fitted into an existing pit?

Fitting a swing-lip leveller into an existing pit normally takes one to two working days per bay, with the bay closed throughout. The work runs in a set order:

1. The old leveller is isolated, lifted out and removed from site.
2. The pit is cleaned and measured, and the edge steel checked for damage.
3. The new leveller is lowered in, set level, and welded or anchored to the pit steel.
4. The hydraulic power pack and control panel are connected, and any interlocks wired.
5. Toe guards, lip and bumpers are checked, then the leveller is run through its full range.

From your side we need the bay emptied and taken out of service, clear access for lifting equipment inside or outside the building, and a suitable power supply, which for most hydraulic levellers is three-phase. If the pit needs repairs, these are done first and can add time, which we confirm in the quote.

What does the free survey cover?

• Scope to convert ground-level doors into docks or add lift tables
• Working hours, shift patterns and windows for out-of-hours work
• Drainage on recessed or sloping dock approaches
• Age and condition of the equipment already in place
• Traffic routes for vehicles and separation of pedestrians
• Bumper position and wear or damage on the dock face

Options to discuss

What do the rules in England mean for the work?

Lift tables and dock lifts in Witney may fall under LOLER, with thorough examination at least every 12 months, or every 6 months where people are lifted. It depends on the equipment and how it is used, and your insurer or competent person will confirm. Dock levellers are usually treated as work equipment under PUWER. We check what applies at survey.

Questions about swing-lip dock levellers in Witney

Swing-lip dock levellers near Witney

Distances are measured from Witney. Nearby towns we cover include Carterton (5 miles), Oxford (10 miles) and Abingdon (12 miles), and other towns in the area are covered too.

• Carterton
• Oxford
• Abingdon
• Cowley
• Didcot
• All of Oxfordshire

Other loading bay services in Witney

• Edge-of-dock levellersCompact levellers fixed to the dock face where there is no pit.
• Loading bay door repairsRepairs to sectional doors, shutters and high-speed doors at the dock.
• Loading bay door automationMotors, controls and safety edges to power an existing manual door.
• Dock traffic lights and interlocksRed and green signals and control interlocks for safe dock sequencing.
• Scissor lift tablesDock lifts that raise goods to trailer height at ground-level doors.
• Dock leveller repairsHydraulic, lip, hinge and control repairs to all common leveller types.

Full guide to swing-lip dock levellers · Everything we do in Witney

Ready to talk about a loading bay in Witney? Call us, or send the details through the quote form.