- Location
- Caterham, Surrey
- Main postcode district
- CR3
- Nearby (straight line)
- Redhill (5 miles), Reigate (6 miles) and Sutton (7 miles)
- Survey and quote
- Free, with a fixed written quote
A sectional loading bay door is an overhead door made from horizontal insulated steel panels hinged together, which run up on rollers in side tracks and park beneath the ceiling or up the wall when open. Panels are commonly 40 to 80 mm thick, so the door seals and insulates better than a single-skin shutter, and it can be operated by hand chain, push-up or electric motor.
How does this suit sites in Caterham?
Our survey for a site in Caterham follows the same approach as anywhere else: measure the opening, check headroom and services, then quote a fixed price. A dock facing the prevailing wind, wherever it sits in Caterham, benefits from a well-sealed sectional door that stops rain and draughts reaching the loading area.
Ageing units around Caterham sometimes have low lintels or pipework above the opening, which a low-headroom or high-lift track can be chosen to work around.
For sectional loading bay doors in Caterham, we begin with a free site survey and a fixed written quote, so you know the scope and cost before committing. We take responsibility for managing the job, and specialist installation engineers carry it out under our supervision. Bays are taken out of use in a planned sequence so the rest of the dock keeps working, and evening or weekend work can be arranged. Each item is tested at handover and the documentation is left with you.
What happens on site when a sectional dock door is installed?
Fitting a sectional dock door often takes around a day per opening once the door is on site, though very large doors or awkward fixings take longer. The bay is out of use while the work is under way.
A typical installation runs like this:
- The old door, if there is one, is taken down and removed from site.
- Steel angles or packers are fixed to the opening so the tracks run true.
- Tracks, springs and panels are assembled and the door is balanced.
- The operator, safety edge, photocells and controls are fitted and wired.
- The door is tested, adjusted and handed over.
Before we arrive you will need a clear area inside the opening for access equipment and the bay taken out of service. Electric doors also need a suitable isolated power supply near the door head, single or three-phase depending on the operator, which we confirm in the quote. On multi-door sites we work bay by bay so the rest of the dock keeps running.
Which track type suits my dock: standard, high-lift or vertical lift?
The right track depends on how much headroom sits above the opening and what is in it. Standard lift track turns the door through a tight radius so it parks just under the ceiling, and suits units with limited space above the lintel.
- Standard lift: needs the least headroom; the open door rests horizontally close to the head of the opening.
- High-lift: the door travels further up the wall before turning, keeping it above lighting, sprinkler pipes or overhead conveyors and away from forklift masts.
- Vertical lift: the door runs straight up the wall and never turns, which suits tall buildings with racking or cranes close to the opening.
- Low headroom: a special track arrangement for openings with very little space above, often found in older units.
We measure headroom, side room and back room at survey and check where lights, ducts and pipework run, because a door that clashes with services cannot open fully. Our door types guide compares sectional doors with shutters and high-speed doors.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What we look at on site
- Escape routes and pedestrian doors close to the bay
- Drainage on recessed or sloping dock approaches
- Temperature requirements for chilled, frozen or ambient goods
- Forklift and pallet truck loads crossing the leveller platform
- Whether planning, building control or a building warrant may be needed
- Control positions, isolators and any existing interlocks
Options to discuss
Thicker insulated panels
Panels at the upper end of the common 40 to 80 mm range improve insulation for heated warehouses and temperature-controlled goods-in areas.
High-lift or vertical lift track
Track arrangements that keep the open door clear of lights, sprinkler pipes, racking and forklift masts in buildings with plenty of height above the opening.
Planning, building control and safety law in England
Workplace safety in England is regulated by HSE. For a loading bay in Caterham, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about sectional loading bay doors in Caterham
What details do you need from us to quote for sectional loading bay doors?
To get started, send the site address in Caterham, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
Can you work outside our normal operating hours in Caterham?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Can you work alongside our main contractor on a new build in Caterham?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Can a sectional dock door be made to fit our existing opening?
Yes, sectional doors are made to measure, so they can be fitted to most existing dock openings. We measure the structural opening, headroom and side room at survey and choose a track to suit. Uneven reveals or a low lintel can usually be dealt with using packers, steel angles or a low-headroom track rather than building work.
What panel thickness should we choose for a heated warehouse?
For most heated warehouses a panel at the thicker end of the common 40 to 80 mm range is the sensible starting point, because it insulates better. Thinner panels can suit unheated stores. New and replacement doors also need to meet the energy rules for your nation, which we check when specifying.
Sectional loading bay doors near Caterham
Businesses outside Caterham may find their nearest town in this list: Redhill (5 miles), Reigate (6 miles) and Sutton (7 miles). Each page covers doors, docks, repairs and servicing.
Other loading bay services in Caterham
Full guide to sectional loading bay doors · Everything we do in Caterham
Have photos of the door, leveller or shelter? Send them with your enquiry and we can give a clearer answer for your Caterham site.