A sectional loading bay door is an overhead door made from horizontal insulated steel panels hinged together, which run up on rollers in side tracks and park beneath the ceiling or up the wall when open. Panels are commonly 40 to 80 mm thick, so the door seals and insulates better than a single-skin shutter, and it can be operated by hand chain, push-up or electric motor.
How does this suit sites in Leicestershire?
Ageing units around Leicestershire sometimes have low lintels or pipework above the opening, which a low-headroom or high-lift track can be chosen to work around. If you are fitting out a new warehouse in Leicestershire, specifying insulated sectional doors from the start avoids disruptive changes once the building is occupied.
Our survey for a site in Leicestershire follows the same approach as anywhere else: measure the opening, check headroom and services, then quote a fixed price.
We never ask you to commit before you have a fixed price. A free survey at your Leicestershire site comes first, followed by a written quote. When the order goes ahead, we plan the installation around your operation, book any out-of-hours working you need and manage the specialist installation engineers on site. The job ends with a full test, a run-through for the people who will use the equipment and a set of handover documents.
Do sectional loading bay doors have to meet energy and safety rules?
Yes. New and replacement sectional loading bay doors fall under building energy rules and workplace safety law, and the detail differs between the four nations.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. Wales, Scotland and Northern Ireland each have their own energy rules, and we confirm the figure that applies to your nation and project.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Workplace (Health, Safety and Welfare) Regulations (Northern Ireland) 1993, require upward-opening doors to have a device that stops them falling back. On a sectional door that usually means spring break and cable break protection.
- Product standard: BS EN 13241 is the product standard for industrial doors, and powered doors are also assessed against BS EN 12453 for safety in use.
- Marking: a powered door in Great Britain may be UKCA or CE marked, while in Northern Ireland it is the CE mark, or CE with UKNI, that applies.
Should a sectional dock door have vision panels or a wicket door?
Vision panels are worth adding on most dock doors, while wicket doors are rarely used on loading bays. A row of double-glazed windows lets staff see whether a trailer is on the bay and brings daylight into the dock area.
- Vision panels can be a single row at eye level or fully glazed sections in aluminium frames.
- Glazed sections lower the door's insulation, so on a heated or chilled building we balance daylight against thermal performance.
- Wicket doors are uncommon on docks because there is a trailer or a drop to the yard behind the door, so they rarely offer a safe exit. A separate pedestrian door beside the bay is usually the better answer.
It is also worth deciding now whether the door will be interlocked with the leveller, so the lip cannot be raised until the door is fully open. Adding links like this later is harder.
Towns we cover in Leicestershire
Choose a town below to see how we handle sectional loading bay doors in that part of Leicestershire.
- Leicester
- Loughborough
- Hinckley
- Coalville
- Wigston Magna
- Melton Mowbray
- Market Harborough
- Oadby
- Earl Shilton
- Mountsorrel
- Castle Donington
- Lutterworth
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
What do the rules in England mean for the work?
Workplace safety in England is regulated by HSE. For a loading bay in Leicestershire, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions
Will you deal with building control and planning for a project in Leicestershire?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
Which building and safety rules apply to a site in Leicestershire?
It depends on which UK nation the site is in. England and Wales use Building Regulations approval, Scotland uses building warrants and Northern Ireland uses building control approval from the council. Workplace safety is regulated by HSE in Great Britain and HSENI in Northern Ireland, and energy rules differ between nations. For your site in Leicestershire, we check what applies at survey and design to it.
Can a sectional dock door be made to fit our existing opening?
Yes, sectional doors are made to measure, so they can be fitted to most existing dock openings. We measure the structural opening, headroom and side room at survey and choose a track to suit. Uneven reveals or a low lintel can usually be dealt with using packers, steel angles or a low-headroom track rather than building work.
Can a manual sectional door be motorised later?
Often yes, if the door is sound and correctly balanced. An operator is fitted to the spring shaft or a trolley drive is fixed to the ceiling, and the door gets a safety edge and photocells at the same time. We check spring condition and balance first, because a motor should never be used to make up for a badly balanced door.
Other services in Leicestershire
Full guide to sectional loading bay doors · All loading bay services in Leicestershire