- Location
- Exeter, Devon
- Main postcode district
- EX2
- Nearby (straight line)
- Exmouth (9 miles), Tiverton (12 miles) and Newton Abbot (14 miles)
- Survey and quote
- Free, with a fixed written quote
A sectional loading bay door is an overhead door made from horizontal insulated steel panels hinged together, which run up on rollers in side tracks and park beneath the ceiling or up the wall when open. Panels are commonly 40 to 80 mm thick, so the door seals and insulates better than a single-skin shutter, and it can be operated by hand chain, push-up or electric motor.
What should sites in Exeter consider?
Ageing units around Exeter sometimes have low lintels or pipework above the opening, which a low-headroom or high-lift track can be chosen to work around. Food and drink businesses in Exeter running temperature-controlled goods-in areas can choose thicker panels to hold conditions steady between deliveries.
For distribution sites in Exeter with heavy daily trailer traffic, an electric sectional door with photocells keeps the bay moving without staff hauling on a chain.
The survey is free, the quote is written and the price is fixed: that is how every installation in Exeter begins. We then manage the work from start to finish. Fitting is carried out by specialist installers under our management, phased so the operation keeps moving, and nights or weekends can be booked by arrangement. On the final day we test the equipment with you and hand over the operating and maintenance information.
How long does a sectional loading bay door last and what wears out?
A sectional dock door can give many years of service, but its working life depends far more on how often it cycles and how often it is hit than on age. The parts that wear are predictable, so planned servicing catches most problems before the door stops.
- Torsion springs: rated for a set number of cycles, so a busy bay uses them up faster than a quiet one.
- Bottom and side seals: crushed by trailers and forklifts, and worth replacing as soon as they split.
- Rollers, hinges and cables: need lubrication and adjustment as the door beds in.
- Bottom panel: the panel most often struck by forklifts; individual panels can usually be replaced.
Bollards or guides inside the opening reduce impact damage. When a door is dented across several panels, the springs are near the end of their cycles and the operator is unreliable, replacement often makes more sense than another repair.
How much does a sectional loading bay door cost?
A sectional loading bay door typically costs £2,400 to £5,200 per door, excluding VAT, supply and fit, for a made-to-measure insulated door fitted and working.
Where your door lands in the range depends on:
- Opening size: larger doors need more panel area, heavier springs and longer track.
- Panel thickness and finish: thicker insulated panels and non-standard colours add cost.
- Track type: high-lift and vertical lift tracks use more steel and fixings than standard lift.
- Operation: an electric operator with safety edge and photocells costs more than chain or push-up operation.
- Vision panels and extras: glazed sections, interlocks to the leveller and links to traffic lights.
- Site conditions: removing an old door, making good the opening, getting power to the door head and out-of-hours working.
We price after a free site survey, and the written quote is the fixed price for the work described. You can compare typical figures on our price guide.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Power supply at each bay, including three-phase availability
- Dock height and the mix of trailers you load
- How often each door cycles during a typical shift
- Yard gradient and the slope of the approach to the dock
- Gaps around trailers where heated or chilled air escapes
- Access for deliveries, cranes or lifting equipment during installation
Options to discuss
Push-up or hand chain operation
Push-up suits small, light doors, while a hand chain makes heavier dock doors easy to open. Both suit bays used a few times a day and need no power supply.
Vision panels
Double-glazed windows or fully glazed aluminium sections let drivers and dock staff see the bay and bring in daylight, at some cost to insulation.
Planning, building control and safety law in England
Sites in Exeter fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies at survey and build any approvals into the plan.
Questions about sectional loading bay doors in Exeter
Will you deal with building control and planning for a project in Exeter?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
What details do you need from us to quote for sectional loading bay doors?
To get started, send the site address in Exeter, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
How do you price sectional loading bay doors for a site in Exeter?
Guide budgets for supply and fit are £2,400 to £5,200 per door, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Can a sectional dock door be made to fit our existing opening?
Yes, sectional doors are made to measure, so they can be fitted to most existing dock openings. We measure the structural opening, headroom and side room at survey and choose a track to suit. Uneven reveals or a low lintel can usually be dealt with using packers, steel angles or a low-headroom track rather than building work.
Will the bay be out of action for long?
Usually only on installation day. The door is made to order before we book the fitting, so the old door stays in use until the new one is ready to go in. On sites with several bays we fit one opening at a time, keeping the rest of the dock running.
Sectional loading bay doors near Exeter
Other towns within reach of Exeter on our coverage list include Exmouth (9 miles), Tiverton (12 miles) and Newton Abbot (14 miles), all covered on the same terms.
Other loading bay services in Exeter
Full guide to sectional loading bay doors · Everything we do in Exeter
Request a quote for your loading bay in Exeter, attaching photos of the dock, the equipment and any damage.