- Location
- Bognor Regis, West Sussex
- Main postcode district
- PO21
- Nearby (straight line)
- Chichester (6 miles), Littlehampton (6 miles) and Emsworth (12 miles)
- Survey and quote
- Free, with a fixed written quote
A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
Where does this fit at a dock in Bognor Regis?
If a manual shutter on a site in Bognor Regis is hard work to open several times a day, a new electric shutter or a retrofit motor may solve it. Low headroom is the deciding factor at many older buildings, whether in Bognor Regis or elsewhere, and a compact roller shutter avoids overhead tracks altogether.
Every shutter we quote for a building in Bognor Regis starts with a survey of the opening, the space above it and how often the door will run.
A single contact at Loading Bay Doors handles your project in Bognor Regis from start to finish. The free site survey and fixed written quote come first, with no obligation to proceed. We then book the installation for times that suit the operation, including out of hours by arrangement, and manage the specialist engineers on site. At the end we commission and test the equipment, walk your team through it and provide the documentation.
What safety and energy rules apply to roller shutters at a dock?
A dock roller shutter must be protected against falling, must not trap anyone if powered, and in a heated building may need insulated laths to meet energy rules.
- Falling back: the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Northern Ireland regulations of 1993, require upward-opening doors to have a device that stops them falling back. On a shutter this is usually a safety brake or anti-fall device on the barrel.
- Trapping: powered shutters need suitable features to prevent trapping, typically a safety edge and photocells, and a way to open by hand, such as a chain override, where needed.
- Energy: in England, Approved Document L (2021) Volume 2 sets a limiting U-value of 1.3 W/m²K for vehicle access doors in new and replacement work. A single-skin steel shutter will not normally reach that figure. Wales, Scotland and Northern Ireland set their own rules, and we confirm the figure for your nation and project.
Our guide to energy rules for loading bay doors explains U-values in more detail.
Is a roller shutter or a sectional door better for a loading bay?
A roller shutter is usually better where headroom is tight, budgets are limited or the building is unheated, while a sectional door is usually better for heated buildings and busy docks that open and close all day.
- Headroom: a shutter coils into a box above the opening; a sectional door needs track running back under the ceiling or up the wall.
- Insulation: insulated sectional panels generally outperform insulated laths.
- Speed: shutters are slower to open and close than most electric sectional doors.
- Security: a closed steel shutter is a robust barrier.
- Repairs: damaged laths can be replaced individually, just as a dented sectional panel can be swapped.
See sectional loading bay doors to compare the two. Where either would work, we can quote both so you can weigh price against performance.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Asbestos register and any other site hazard information
- Bumper position and wear or damage on the dock face
- Headroom above the opening and which track type will suit it
- How drivers are prevented from pulling away too early
- Control positions, isolators and any existing interlocks
- Traffic routes for vehicles and separation of pedestrians
Options to discuss
Insulated lath shutter
Foam-filled twin-skin laths that improve thermal performance and reduce noise, for heated goods-in areas where headroom rules out a sectional door.
Aluminium shutter
Lighter laths that resist corrosion, suited to coastal sites, washdown areas and large openings where a lighter curtain puts less strain on the motor.
Regulations and approvals in England
Workplace safety in England is regulated by HSE. For a loading bay in Bognor Regis, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about roller shutter loading bay doors in Bognor Regis
Do you cover Bognor Regis for roller shutter loading bay doors?
Yes. We take on roller shutter loading bay doors for businesses in Bognor Regis and across West Sussex. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
How do you price roller shutter loading bay doors for a site in Bognor Regis?
Guide budgets for supply and fit are £1,600 to £4,800 per door, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
Can you work alongside our main contractor on a new build in Bognor Regis?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
How long does a new roller shutter take to arrive?
Shutters are made to measure, so the lead time depends on size, lath type and finish, and we confirm it in the written quote. The existing door stays in use until the new shutter is ready, and installation is then booked for a time that suits your operation.
Are roller shutters noisy at a loading bay?
A roller shutter is generally noisier than a sectional door because the laths move against each other as they coil, though insulated laths and well-adjusted guides reduce this. Noise matters most where the dock is close to offices or neighbours. Keeping the barrel and guides clean and lubricated keeps running noise down.
Roller shutter loading bay doors near Bognor Regis
Close neighbours of Bognor Regis with their own pages here: Chichester (6 miles), Littlehampton (6 miles) and Emsworth (12 miles). Choose one to see coverage details for that town.
Other loading bay services in Bognor Regis
Full guide to roller shutter loading bay doors · Everything we do in Bognor Regis
Ready to talk about a loading bay in Bognor Regis? Call us, or send the details through the quote form.