- Location
- Havant, Hampshire
- Main postcode district
- PO9
- Nearby (straight line)
- Emsworth (2 miles), Waterlooville (3 miles) and Portsmouth (6 miles)
- Survey and quote
- Free, with a fixed written quote
A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
What should sites in Havant consider?
Timber yards and builders merchants in Havant handling long loads and heavy forklift traffic can benefit from strong steel shutters that tolerate knocks. Docks that face an open yard in Havant can catch strong gusts, so we check orientation and specify end locks and heavier laths where exposure calls for it.
Every shutter we quote for a building in Havant starts with a survey of the opening, the space above it and how often the door will run.
Your loading bay stays our responsibility from the survey to the handover. In Havant, the survey and written quote are free, and the quoted price is fixed for the agreed scope. Installation is carried out by specialist engineers working under our management, at times planned with you to protect your loading schedule. Out-of-hours work is available by arrangement. We finish by testing the equipment and handing over its documentation.
Can a roller shutter cope with high winds at an exposed dock?
Yes, if it is specified for the exposure. Wind pushes the curtain inwards or draws it outwards, and on a wide opening that load can pull laths out of their guides or bow the whole curtain.
For exposed docks we typically consider:
- End locks: clips on the ends of the laths that hold the curtain inside the guides under load.
- Deeper guides: give the end locks more to hold on to.
- Heavier gauge or profiled laths: stiffer across wide openings.
- Intermediate wind bars: horizontal reinforcement on very large shutters.
Openings that face open yards, sit at the end of a building or are funnelled between units tend to see the strongest gusts. We note orientation and surroundings at survey and choose a wind-resistant build where it is needed, rather than adding cost to every door on the site.
How is a roller shutter fitted to an existing loading bay opening?
A roller shutter is fitted either behind the opening on the inside face or between the reveals, with guides fixed down each side and the barrel mounted on brackets above. Fitting usually takes a day or less per opening once the shutter is on site.
The work normally includes:
- Removing and disposing of the old door or shutter.
- Checking the lintel and reveals will take the fixings, and adding steel packers if not.
- Fixing the guides, brackets and barrel, then running the curtain onto the barrel.
- Fitting the motor, controls, safety edge and photocells on electric shutters.
- Setting limits, testing the safety brake and demonstrating the manual override.
You will need to clear the area inside the opening and take the bay out of use. An electric shutter also needs a suitable isolated power supply near the barrel, which we can include in the quote if one is not already there.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Wind exposure at the dock, which affects door and shelter choice
- Gaps around trailers where heated or chilled air escapes
- How often each door cycles during a typical shift
- Yard gradient and the slope of the approach to the dock
- Age and condition of the equipment already in place
- Wall and steel structure for door, shelter and bumper fixings
Options to discuss
Aluminium shutter
Lighter laths that resist corrosion, suited to coastal sites, washdown areas and large openings where a lighter curtain puts less strain on the motor.
Wind-resistant build
End locks, deeper guides and heavier gauge laths for wide or exposed openings where gusts could pull the curtain out of its guides.
Which rules apply in England?
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Havant. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about roller shutter loading bay doors in Havant
Can you work alongside our main contractor on a new build in Havant?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Havant site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Do you cover Havant for roller shutter loading bay doors?
Yes. We take on roller shutter loading bay doors for businesses in Havant and across Hampshire. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
Do roller shutters work on cold store docks?
Roller shutters are rarely used as the main door on a cold store dock, because even insulated laths do not hold temperature as well as a purpose-made cold store door. They can work as an outer security door in front of an insulated door, or at ambient bays on the same site.
Are roller shutters noisy at a loading bay?
A roller shutter is generally noisier than a sectional door because the laths move against each other as they coil, though insulated laths and well-adjusted guides reduce this. Noise matters most where the dock is close to offices or neighbours. Keeping the barrel and guides clean and lubricated keeps running noise down.
Roller shutter loading bay doors near Havant
The same survey, quote and repair service is available in towns around Havant, such as Emsworth (2 miles), Waterlooville (3 miles) and Portsmouth (6 miles).
Other loading bay services in Havant
Full guide to roller shutter loading bay doors · Everything we do in Havant
Use the quote tool to tell us about the doors, levellers or shelters at your Havant site, and we will be in touch to arrange the next step.