- Location
- Farnborough, Hampshire
- Main postcode district
- GU11
- Nearby (straight line)
- Camberley (3 miles), Aldershot (3 miles) and Fleet (3 miles)
- Survey and quote
- Free, with a fixed written quote
A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
Why do sites in Farnborough choose this?
Every shutter we quote for a building in Farnborough starts with a survey of the opening, the space above it and how often the door will run. If a manual shutter on a site in Farnborough is hard work to open several times a day, a new electric shutter or a retrofit motor may solve it.
Docks that face an open yard in Farnborough can catch strong gusts, so we check orientation and specify end locks and heavier laths where exposure calls for it.
If you are planning roller shutter loading bay doors for a site in Farnborough, expect four stages. A free survey and fixed written quote come first. We then agree a programme with you, including any out-of-hours work. Specialist installation engineers carry out the installation under our management, with us as your single point of contact. Finally, the equipment is tested, your staff are shown how it works and everything is handed over with its documentation.
Which lath should I choose: single skin, insulated or aluminium?
Choose single-skin steel for unheated buildings where cost and strength matter most, insulated laths where the building is heated, and aluminium where weight or corrosion is the main concern.
- Single-skin steel: strong and economical, ideal for unheated stores, trade counters and secure external openings, but it offers little insulation.
- Insulated steel laths: twin-skin laths filled with foam improve thermal performance and reduce noise. The coil is larger, so the box above the opening is bigger.
- Aluminium laths: lighter and corrosion resistant, useful in coastal or washdown environments, and easier on the motor at large openings.
- Perforated or punched laths: let light and air through while keeping the opening secure, better suited to internal cages than external docks.
Lath gauge and profile matter too. Heavier gauges resist forklift knocks and wind better, and we specify them for wide or exposed openings.
Can a roller shutter cope with high winds at an exposed dock?
Yes, if it is specified for the exposure. Wind pushes the curtain inwards or draws it outwards, and on a wide opening that load can pull laths out of their guides or bow the whole curtain.
For exposed docks we typically consider:
- End locks: clips on the ends of the laths that hold the curtain inside the guides under load.
- Deeper guides: give the end locks more to hold on to.
- Heavier gauge or profiled laths: stiffer across wide openings.
- Intermediate wind bars: horizontal reinforcement on very large shutters.
Openings that face open yards, sit at the end of a building or are funnelled between units tend to see the strongest gusts. We note orientation and surroundings at survey and choose a wind-resistant build where it is needed, rather than adding cost to every door on the site.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Condition of any existing leveller pit, kerb angles and pit drainage
- Temperature requirements for chilled, frozen or ambient goods
- Access for deliveries, cranes or lifting equipment during installation
- Traffic routes for vehicles and separation of pedestrians
- Control positions, isolators and any existing interlocks
- Whether planning, building control or a building warrant may be needed
Options to discuss
Aluminium shutter
Lighter laths that resist corrosion, suited to coastal sites, washdown areas and large openings where a lighter curtain puts less strain on the motor.
Insulated lath shutter
Foam-filled twin-skin laths that improve thermal performance and reduce noise, for heated goods-in areas where headroom rules out a sectional door.
Regulations and approvals in England
Workplace safety in England is regulated by HSE. For a loading bay in Farnborough, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about roller shutter loading bay doors in Farnborough
Is VAT included in your guide prices for roller shutter loading bay doors?
No. Our customers are businesses, so guide prices exclude VAT, which is added at the standard rate. The same guide range applies in Hampshire as everywhere else: for roller shutter loading bay doors, it is £1,600 to £4,800 per door, excluding VAT. It covers supply and fit for a typical installation. Your fixed written quote after the free survey shows the net price, the VAT and exactly what is included.
Do you cover Farnborough for roller shutter loading bay doors?
Yes. We take on roller shutter loading bay doors for businesses in Farnborough and across Hampshire. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
Can you work alongside our main contractor on a new build in Farnborough?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Can an existing manual shutter be motorised?
Often yes. If the barrel, end plates and curtain are in good condition, an external or tubular motor can be added with controls and safety devices. Older or heavier shutters sometimes need a stronger barrel first, and a badly worn curtain is usually better replaced at the same time.
How long does a new roller shutter take to arrive?
Shutters are made to measure, so the lead time depends on size, lath type and finish, and we confirm it in the written quote. The existing door stays in use until the new shutter is ready, and installation is then booked for a time that suits your operation.
Roller shutter loading bay doors near Farnborough
Nearby places we cover, measured from Farnborough, include Camberley (3 miles), Aldershot (3 miles) and Fleet (3 miles). Ask if your own town is missing.
Other loading bay services in Farnborough
Full guide to roller shutter loading bay doors · Everything we do in Farnborough
Get in touch about loading bay doors and dock equipment in Farnborough: call, email or use the quote tool.