Loading bay servicing covers planned preventive maintenance of dock equipment at agreed intervals. An engineer checks, adjusts and lubricates doors, levellers, shelters, seals, restraints, traffic lights and lift tables, tests safety devices and records defects in a written report. Servicing supports, but is separate from, insurer inspections and the LOLER thorough examinations that some equipment needs.
Where does this fit at a dock in Glasgow and Dunbartonshire?
Mixed-age dock equipment at older sites in Glasgow and Dunbartonshire benefits from a first service that records the condition of every item and prioritises any repairs. Lift tables at warehouses in Glasgow and Dunbartonshire need a LOLER thorough examination regime alongside servicing, and the two can be scheduled to suit the operation.
Servicing for dock equipment in Glasgow and Dunbartonshire is priced per item per visit and agreed in writing before the first engineer attends site.
We do not turn up and then name a price. Every repair or service visit in Glasgow and Dunbartonshire is agreed in writing first, including what the charge covers. Sending photos of the damage, error codes or leaks helps us diagnose the problem before travelling and bring the likely parts. Any additional work found on the day is quoted for your approval before it starts. You then get a written report for your records.
What does a loading bay service visit include?
A loading bay service visit includes checking, adjusting and lubricating each item, testing its safety devices and recording its condition. Typical checks by equipment type:
- Doors: springs, cables, balance, rollers, hinges, tracks, safety edges, photocells, fall-back devices, controls and manual operation.
- Levellers: hydraulic leaks and oil level, hoses, cylinders, lip and hinges, deck condition, toe guards, controls and the maintenance strut.
- Shelters and seals: curtains, frames, pads, covers, airbags and blowers.
- Restraints, lights and interlocks: engagement, sensors and the full interlock sequence.
- Bumpers and wheel guides: wear and fixings.
- Lift tables: toe guards, bellows, hydraulics, controls and gates.
Minor adjustments and lubrication are part of the service. Anything needing parts or more time is recorded and quoted as a repair, so you stay in control of spend.
How much does loading bay servicing cost?
Loading bay servicing typically costs £85 to £180 per item per visit, excluding VAT, where an item is one door, leveller, shelter, restraint or lift table. Simple items such as a dock seal sit towards the lower end; high-speed doors and lift tables sit towards the top.
How the price is agreed:
- You send a list of equipment, with photos or asset labels if you have them.
- We agree the price per item and the visit schedule in writing before the first visit.
- Repairs found during a service are quoted separately and only done once you approve them.
What moves the price:
- Equipment type: powered doors, levellers and lift tables take longer than seals and lights.
- Number of items: larger sites spread travel and set-up across more items.
- Frequency: the number of visits a year.
- Timing: out-of-hours visits cost more.
- Location: remote and island sites carry travel costs, shown in advance.
VAT is added at the standard rate.
Towns we cover in Glasgow and Dunbartonshire
We cover loading bay servicing throughout Glasgow and Dunbartonshire, and the towns below each have their own page. If yours is not listed, get in touch anyway.
The visit price is agreed before anyone attends. All guide prices.
Planning, building control and safety law in Scotland
Doors and dock equipment installed in Scotland may carry the UKCA or the CE mark, and we pass on the documentation for everything fitted in Glasgow and Dunbartonshire. Because building warrant and planning questions can affect the programme, we check what applies before any work starts and raise any approvals early rather than assuming none are needed.
Questions
Do you provide a written report after each visit?
Yes. After every repair or service visit to a site in Glasgow and Dunbartonshire, you receive a written report setting out what was checked, what was found, what work was carried out and anything that still needs attention, with a quote for further work where needed. The report is useful for your maintenance records and for discussions with your insurer or inspector.
How often should equipment at our Glasgow and Dunbartonshire site be serviced?
It depends on how hard the equipment works and on the manufacturer's recommendations. A multi-shift dock with frequent trailer movements needs more attention than a door that opens a few times a day. We suggest a schedule after looking at the equipment and how it is used, and we can line visits up with your insurance inspections where that helps.
Can servicing be carried out outside operating hours?
Yes, servicing can be arranged for evenings or weekends where daytime access is difficult. Out-of-hours visits cost more, and that price is agreed in writing before the visit. Many sites prefer quieter periods so bays can be released without affecting trailer arrivals.
Is loading bay servicing the same as an insurer inspection?
No. Servicing is planned maintenance that keeps equipment working and safe, while an insurer inspection is an independent check, commonly every 12 months for levellers under PUWER. Many sites schedule a service shortly before each inspection, so routine defects are dealt with before the inspector attends.
Other services in Glasgow and Dunbartonshire
Full guide to loading bay servicing · All loading bay services in Glasgow and Dunbartonshire