A loading bay door automation package is an electric operator, control panel and set of safety devices fitted to an existing manual sectional door or roller shutter so it opens and closes at the press of a button. Once motorised, the door is a power-operated door, so it needs protection against trapping, such as a safety edge and photocells, and a way to be opened by hand if the power fails.
Is this right for your site in Glasgow and Dunbartonshire?
Heavy shutters on trade and merchant sites in Glasgow and Dunbartonshire can be tiring to open by hand, which is where an external chain-drive motor earns its place. Teams working on cold or wet docks in Glasgow and Dunbartonshire tend to leave doors open if they are hard to operate, so motorising them can help keep heat in.
On older units in Glasgow and Dunbartonshire where the original doors are still sound, automation keeps the existing door working while removing the effort of hand chains.
Keeping the dock running is usually the first concern, so we plan around it. After a free survey of your Glasgow and Dunbartonshire site and a written quote at a fixed price, we agree when each bay can be released and whether any work should happen out of hours. Specialist installation engineers working under our management then fit the equipment, and we test it and hand over the documentation before the bay goes back into use.
What safety rules apply once a manual door is motorised?
Once a manual door is fitted with a motor it becomes a power-operated door, and the rules for powered doors apply in full. Automation is more than bolting on a motor.
- Workplace law: regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992 in Great Britain, and the Workplace (Health, Safety and Welfare) Regulations (Northern Ireland) 1993, require powered doors to have suitable and effective features to prevent trapping, and to be operable by hand where necessary unless they open automatically on power failure.
- Safety in use: BS EN 12453 sets out safety requirements and test methods for power-operated doors, including how closing forces are limited and measured.
- Product standard: BS EN 13241 covers the door as a product.
- Marking: in Great Britain a powered door may carry the UKCA or the CE mark; in Northern Ireland the CE mark, or CE with UKNI, applies.
Enforcement sits with HSE in Great Britain and HSENI in Northern Ireland. The results of the safety checks carried out at commissioning form part of the handover.
How much does it cost to motorise a loading bay door?
Automating an existing loading bay door typically costs £1,100 to £2,400 per door, excluding VAT, supply and fit. That covers the operator, control panel, safety devices, wiring at the door and commissioning.
What moves the price:
- Door type and weight: heavy shutters and large sectional doors need more powerful operators.
- Operator type: shaft-mounted, trolley, tubular or external chain-drive.
- Control mode: hold-to-run controls need fewer safety devices than impulse or automatic operation.
- Safety devices: safety edge, photocells and, for automatic closing, additional sensing.
- Extras: remote controls, pull cords, induction loops and interlocks with levellers or traffic lights.
- Power: whether a suitable isolated supply already exists near the door.
If the door needs work before it can be motorised, such as new springs or rollers, we price that separately so you can see each cost. The written quote after a free site survey is the fixed price.
Towns we cover in Glasgow and Dunbartonshire
Choose a town below to see how we handle loading bay door automation in that part of Glasgow and Dunbartonshire.
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
Which rules apply in Scotland?
Doors and dock equipment installed in Scotland may carry the UKCA or the CE mark, and we pass on the documentation for everything fitted in Glasgow and Dunbartonshire. Because building warrant and planning questions can affect the programme, we check what applies at survey and raise any approvals early rather than assuming none are needed.
Questions
Will you deal with building control and planning for a project in Glasgow and Dunbartonshire?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
Can you work outside our normal operating hours in Glasgow and Dunbartonshire?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
Can any manual door be motorised?
No, only doors that are sound, balanced and run smoothly by hand should be motorised. Doors with weak springs, damaged panels, bent laths or obsolete parts may need repair first, or may be better replaced. We check this at survey and tell you which applies before quoting.
How long does it take to automate a dock door?
Most automations are completed within a working day per door, once any repairs to the door itself have been done. Larger shutters, or doors that need a new power supply, can take longer. We plan the work so that only the door being automated is out of use.
Other services in Glasgow and Dunbartonshire
Full guide to loading bay door automation · All loading bay services in Glasgow and Dunbartonshire