- Location
- Solihull, West Midlands
- Main postcode district
- B91
- Nearby (straight line)
- Shirley (2 miles), Washwood Heath (6 miles) and Coleshill (7 miles)
- Survey and quote
- Free, with a fixed written quote
A loading bay door automation package is an electric operator, control panel and set of safety devices fitted to an existing manual sectional door or roller shutter so it opens and closes at the press of a button. Once motorised, the door is a power-operated door, so it needs protection against trapping, such as a safety edge and photocells, and a way to be opened by hand if the power fails.
Why do sites in Solihull choose this?
Operations in Solihull with manual sectional doors in good condition can often add an electric operator for much less than the cost of a new door. Landlords upgrading manual doors across a multi-let estate in Solihull can standardise operators and controls so every tenant gets the same reliable setup.
Any automation project in Solihull begins with checking the door by hand, because a motor cannot make up for weak springs or worn rollers.
Here is what happens after you contact us about a site in Solihull. We arrange a free survey, measure up and send a fixed written quote. If you go ahead, we manage the whole job, including ordering, delivery and coordination with your site team. Specialist installation engineers working under our management do the fitting, at times built around your loading schedule, with out-of-hours work by arrangement. Testing and handover documents close the job.
What is involved in fitting a motor to an existing dock door?
Fitting a motor to an existing dock door usually takes a few hours to a day per door, and starts with checking that the door itself is safe to automate.
- The door is checked for balance, spring condition, cable wear and track alignment.
- The operator is mounted on the shaft, ceiling rail or barrel bracket.
- The control panel is fixed in a safe position with a clear view of the door.
- A safety edge is fitted to the bottom rail and photocells are set across the opening.
- Limits, forces and controls are set, then the door is tested against the relevant safety checks.
You will need to provide a suitable isolated power supply near the door, or ask us to include it, and keep the door out of use during the work. Single-phase supplies suit many operators, but larger industrial operators may need three-phase power, which we confirm at survey.
Is my existing door suitable for automation?
An existing door is usually suitable for automation if it is structurally sound, correctly balanced and runs smoothly by hand. A motor should never be used to make up for a door that is heavy, stiff or damaged.
Signs a door can be automated:
- It lifts evenly by hand and stays put when released halfway.
- Springs, cables, rollers and tracks are in good order.
- Panels or laths are not badly dented or distorted.
Signs it may be better replaced:
- Springs are near the end of their life or have broken before.
- The door is single skin and the building is now heated.
- Parts are no longer available for the door model.
Where replacement makes more sense, we will say so and can quote for sectional loading bay doors supplied with an operator already fitted, so you can compare the two routes on cost.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- Wind exposure at the dock, which affects door and shelter choice
- Wall and steel structure for door, shelter and bumper fixings
- How often each door cycles during a typical shift
- Condition of any existing leveller pit, kerb angles and pit drainage
- Power supply at each bay, including three-phase availability
- Working hours, shift patterns and windows for out-of-hours work
Options to discuss
Dock interlocks
Wiring that links the door to levellers, shelters, restraints or traffic lights so the dock can only run in a safe sequence.
Tubular or external shutter motor
A motor inside the barrel for small and medium shutters, or a side-mounted chain-drive unit for large, heavy shutters at busy openings.
Regulations and approvals in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Solihull. Planning and Building Regulations questions are never assumed either way: we check what applies at survey, so you know before work is booked.
Questions about loading bay door automation in Solihull
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Solihull site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Will you deal with building control and planning for a project in Solihull?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
How do you price loading bay door automation for a site in Solihull?
Guide budgets for supply and fit are £1,100 to £2,400 per door, excluding VAT. The figure moves with size, insulation, the operator, electrics, access, any pit or groundworks and out-of-hours working. Where levellers are involved, the guide assumes an existing, sound pit. After the free survey you receive a fixed written quote, and that is the price for the agreed scope.
How long does it take to automate a dock door?
Most automations are completed within a working day per door, once any repairs to the door itself have been done. Larger shutters, or doors that need a new power supply, can take longer. We plan the work so that only the door being automated is out of use.
What is the difference between hold-to-run and impulse control?
With hold-to-run the operator must keep pressing the button for the door to move, so they watch it throughout. With impulse control a single press opens or closes the door fully, which saves time but requires full safety sensing such as a safety edge and photocells, because no one may be watching.
Loading bay door automation near Solihull
Businesses outside Solihull may find their nearest town in this list: Shirley (2 miles), Washwood Heath (6 miles) and Coleshill (7 miles). Each page covers doors, docks, repairs and servicing.
Other loading bay services in Solihull
Full guide to loading bay door automation · Everything we do in Solihull
Tell us what is happening at your Solihull dock, what equipment is there and when it is used, and we will suggest the right next step.