- Location
- Solihull, West Midlands
- Main postcode district
- B91
- Nearby (straight line)
- Shirley (2 miles), Washwood Heath (6 miles) and Coleshill (7 miles)
- Survey and quote
- Free, with a fixed written quote
A roller shutter loading bay door is a door made from interlocking horizontal slats, called laths, that coil around a barrel in a box above the opening. Because it rolls up into a compact space, a shutter needs little headroom and no ceiling tracks, which suits older units, low-headroom openings and buildings with cranes, pipes or racking close above the door.
How does this suit sites in Solihull?
Timber yards and builders merchants in Solihull handling long loads and heavy forklift traffic can benefit from strong steel shutters that tolerate knocks. Where a site in Solihull is exposed to salt air or regular washdown, aluminium laths or a good powder coat help slow corrosion on the curtain and guides.
Docks that face an open yard in Solihull can catch strong gusts, so we check orientation and specify end locks and heavier laths where exposure calls for it.
Keeping the dock running is usually the first concern, so we plan around it. After a free survey of your Solihull site and a written quote at a fixed price, we agree when each bay can be released and whether any work should happen out of hours. Specialist installation engineers working under our management then fit the equipment, and we test it and hand over the documentation before the bay goes back into use.
How is a roller shutter fitted to an existing loading bay opening?
A roller shutter is fitted either behind the opening on the inside face or between the reveals, with guides fixed down each side and the barrel mounted on brackets above. Fitting usually takes a day or less per opening once the shutter is on site.
The work normally includes:
- Removing and disposing of the old door or shutter.
- Checking the lintel and reveals will take the fixings, and adding steel packers if not.
- Fixing the guides, brackets and barrel, then running the curtain onto the barrel.
- Fitting the motor, controls, safety edge and photocells on electric shutters.
- Setting limits, testing the safety brake and demonstrating the manual override.
You will need to clear the area inside the opening and take the bay out of use. An electric shutter also needs a suitable isolated power supply near the barrel, which we can include in the quote if one is not already there.
Is a roller shutter or a sectional door better for a loading bay?
A roller shutter is usually better where headroom is tight, budgets are limited or the building is unheated, while a sectional door is usually better for heated buildings and busy docks that open and close all day.
- Headroom: a shutter coils into a box above the opening; a sectional door needs track running back under the ceiling or up the wall.
- Insulation: insulated sectional panels generally outperform insulated laths.
- Speed: shutters are slower to open and close than most electric sectional doors.
- Security: a closed steel shutter is a robust barrier.
- Repairs: damaged laths can be replaced individually, just as a dented sectional panel can be swapped.
See sectional loading bay doors to compare the two. Where either would work, we can quote both so you can weigh price against performance.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
Survey checklist for your dock
- Whether planning, building control or a building warrant may be needed
- Access for deliveries, cranes or lifting equipment during installation
- Power supply at each bay, including three-phase availability
- Headroom above the opening and which track type will suit it
- Wheel guide positions and yard markings for reversing vehicles
- Asbestos register and any other site hazard information
Options to discuss
Insulated lath shutter
Foam-filled twin-skin laths that improve thermal performance and reduce noise, for heated goods-in areas where headroom rules out a sectional door.
Wind-resistant build
End locks, deeper guides and heavier gauge laths for wide or exposed openings where gusts could pull the curtain out of its guides.
Regulations and approvals in England
Workplace safety in England is regulated by HSE. For a loading bay in Solihull, that means doors meeting regulation 18 of the Workplace (Health, Safety and Welfare) Regulations 1992, equipment maintained under PUWER and suitable safeguards against vehicles driving away too early. We check what applies at survey and design the bay accordingly.
Questions about roller shutter loading bay doors in Solihull
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Solihull site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Is the site survey in Solihull free?
Yes. For new installations, replacements, upgrades, conversions and complete bays, the site survey and written quote are free and come with no obligation. The survey lets us measure the openings, check the dock and structure, and understand how the bay is used, so the quote reflects your site. Repair and servicing visits are different: they are chargeable, with the price agreed before anyone attends.
Can you work alongside our main contractor on a new build in Solihull?
Yes. For new warehouses and fit-outs, we can supply and install the dock package as part of a wider project, working to the main contractor's programme, site rules and permits. We will need drawings, dock levels and the programme, and we coordinate pit details, power supplies and door openings with the relevant trades before installation begins.
Do roller shutters work on cold store docks?
Roller shutters are rarely used as the main door on a cold store dock, because even insulated laths do not hold temperature as well as a purpose-made cold store door. They can work as an outer security door in front of an insulated door, or at ambient bays on the same site.
Are roller shutters noisy at a loading bay?
A roller shutter is generally noisier than a sectional door because the laths move against each other as they coil, though insulated laths and well-adjusted guides reduce this. Noise matters most where the dock is close to offices or neighbours. Keeping the barrel and guides clean and lubricated keeps running noise down.
Roller shutter loading bay doors near Solihull
Other towns within reach of Solihull on our coverage list include Shirley (2 miles), Washwood Heath (6 miles) and Coleshill (7 miles), all covered on the same terms.
Other loading bay services in Solihull
Full guide to roller shutter loading bay doors · Everything we do in Solihull
Request a quote for your loading bay in Solihull, attaching photos of the dock, the equipment and any damage.