- Location
- Reigate, Surrey
- Main postcode district
- RH2
- Nearby (straight line)
- Redhill (2 miles), Horley (5 miles) and Dorking (6 miles)
- Survey and quote
- Free, with a fixed written quote
A loading bay door automation package is an electric operator, control panel and set of safety devices fitted to an existing manual sectional door or roller shutter so it opens and closes at the press of a button. Once motorised, the door is a power-operated door, so it needs protection against trapping, such as a safety edge and photocells, and a way to be opened by hand if the power fails.
Where does this fit at a dock in Reigate?
Any automation project in Reigate begins with checking the door by hand, because a motor cannot make up for weak springs or worn rollers. Upgrading manual docks to electric operation is a practical first step for sites in Reigate that later plan to add interlocks and traffic lights.
On older units in Reigate where the original doors are still sound, automation keeps the existing door working while removing the effort of hand chains.
How does an installation in Reigate work? First, a free, no-obligation survey to measure up and understand the operation. Next, a fixed written quote. Then a programme agreed with you, so the work fits around deliveries, with out-of-hours slots if needed. The installation itself is carried out by specialist engineers who answer to us, and it finishes with testing, a walk-through for your staff and a handover pack.
What is involved in fitting a motor to an existing dock door?
Fitting a motor to an existing dock door usually takes a few hours to a day per door, and starts with checking that the door itself is safe to automate.
- The door is checked for balance, spring condition, cable wear and track alignment.
- The operator is mounted on the shaft, ceiling rail or barrel bracket.
- The control panel is fixed in a safe position with a clear view of the door.
- A safety edge is fitted to the bottom rail and photocells are set across the opening.
- Limits, forces and controls are set, then the door is tested against the relevant safety checks.
You will need to provide a suitable isolated power supply near the door, or ask us to include it, and keep the door out of use during the work. Single-phase supplies suit many operators, but larger industrial operators may need three-phase power, which we confirm at survey.
Which type of door operator is right for my door?
The right operator depends on the door type, its weight and how many times a day it runs. Matching the operator's duty cycle to real use is what stops motors overheating and failing early.
- Shaft-mounted operator: fits directly on the spring shaft of a sectional door. Compact, strong and suited to heavy, busy dock doors.
- Trolley operator: runs along a rail on the ceiling and pulls the door. Suits lighter sectional doors on quieter bays.
- Tubular motor: sits inside the barrel of a roller shutter, keeping the installation tidy on small and medium shutters.
- External or side-mounted motor: drives a shutter barrel by chain, for larger and heavier shutters.
Every option should include a manual override, either a hand chain or a release, so the door can be used during a power cut. On bays that cycle many times an hour we specify an industrial operator rated for that duty rather than a light-use unit.
The same published guide range applies across England; access, out-of-hours working and site conditions are confirmed at the free survey.
What does the free survey cover?
- Yard gradient and the slope of the approach to the dock
- Bumper position and wear or damage on the dock face
- Control positions, isolators and any existing interlocks
- Condition of any existing leveller pit, kerb angles and pit drainage
- Forklift and pallet truck loads crossing the leveller platform
- Drainage on recessed or sloping dock approaches
Options to discuss
Tubular or external shutter motor
A motor inside the barrel for small and medium shutters, or a side-mounted chain-drive unit for large, heavy shutters at busy openings.
Shaft-mounted operator
A compact industrial motor that fits directly onto the spring shaft of a sectional door, suited to heavy dock doors and bays that run many cycles a day.
Regulations and approvals in England
In England, Approved Document L (2021) sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. That shapes door specification for sites in Reigate, so we confirm the requirement for your project and check what applies at survey before recommending a door.
Questions about loading bay door automation in Reigate
What details do you need from us to quote for loading bay door automation?
To get started, send the site address in Reigate, the number of bays or openings, approximate sizes, and photos of the dock from inside and outside. Tell us what vehicles you load, what goods you handle and any temperature requirements. Drawings help on new builds. We then arrange the free survey and confirm the details before the written quote is issued.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Reigate site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
How long does installation take at a site in Reigate?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
How long does it take to automate a dock door?
Most automations are completed within a working day per door, once any repairs to the door itself have been done. Larger shutters, or doors that need a new power supply, can take longer. We plan the work so that only the door being automated is out of use.
Can drivers open the door without leaving the forklift?
Yes, pull cords, radio remotes and induction loops in the floor can all open a powered door without the driver getting down. The right choice depends on traffic, and any opening method that does not need a button held must be paired with safety devices so the door cannot close on a vehicle or person.
Loading bay door automation near Reigate
Sites close to Reigate get the same service, including those in Redhill (2 miles), Horley (5 miles) and Dorking (6 miles), with every job run the same way.
Other loading bay services in Reigate
Full guide to loading bay door automation · Everything we do in Reigate
Send a few photos of the dock and a short description of the problem, and we will come back to you about your Reigate site.