A high-speed dock door is a power-operated door with a flexible PVC fabric curtain that opens and closes much faster than a conventional sectional door or shutter, usually driven by a frequency-controlled motor. Many versions use a self-repairing curtain or breakaway bottom bar, so a forklift strike pushes the curtain out of its guides instead of wrecking it, and the door re-engages itself on the next cycle.
How does this suit sites in Tyne and Wear?
Whether your site in Tyne and Wear is a new build or an older unit, we survey the opening, traffic and power before recommending any high-speed door. Busy cross-dock and parcel operations in Tyne and Wear can use a high-speed door behind the main dock door to keep traffic flowing while limiting the time the bay stands open.
Yards that are open to the weather in Tyne and Wear may need a wind-reinforced build, because a standard internal high-speed door is not designed for gusts at an external opening.
Here is what happens after you contact us about a site in Tyne and Wear. We arrange a free survey, measure up and send a fixed written quote. If you go ahead, we manage the whole job, including ordering, delivery and coordination with your site team. Specialist installation engineers working under our management do the fitting, at times built around your loading schedule, with out-of-hours work by arrangement. Testing and handover documents close the job.
What does a high-speed door installation need from our site?
A high-speed door installation needs a sound opening to fix the side frames to, a suitable power supply near the door, and the opening taken out of use on the day of fitting.
Before we attend, please make sure:
- a dedicated supply with a local isolator is in place near the door head, or is included in our quote,
- the floor at the threshold is level, as the bottom edge needs a consistent landing,
- stock, racking and vehicles are cleared from both sides of the opening,
- your team has agreed where push buttons, pull cords or radar sensors should sit, based on traffic routes.
On site, engineers working under our management fit the frames and drive unit, hang the curtain, wire the control panel and light curtain, then set opening heights and speeds. Where the door sits behind an existing sectional door, we also wire the interlock so the two doors work in sequence.
Should a high-speed door replace our strip curtain or work alongside our dock door?
At very busy openings a high-speed door often replaces a strip curtain, and at external docks it usually works alongside a slower insulated door rather than replacing it.
Strip curtains are inexpensive, but they slow forklifts, scratch quickly and can hide a pedestrian on the other side. A high-speed door clears the opening fully, closes again within seconds and keeps a clear view through its vision panels. See PVC strip curtains if you are weighing up the two.
At external docks, a common arrangement is:
- an insulated sectional door on the outside for security and closing at night,
- a high-speed door just inside it for daytime traffic,
- an interlock so the high-speed door only runs when the outer door is open.
This pairing keeps the building secure out of hours while cutting the time the opening stands open during the working day.
Towns we cover in Tyne and Wear
Choose a town below to see how we handle high-speed dock doors in that part of Tyne and Wear.
- Newcastle upon Tyne
- Sunderland
- South Shields
- Gateshead
- Washington
- Tynemouth
- Wallsend
- Newburn
- North Shields
- Whitley Bay
- Houghton-le-Spring
- Felling
- Jarrow
- Gosforth
- Hebburn
- Whickham
- Blaydon-on-Tyne
Budget range for supply and fit. The written quote after a free survey is the fixed price. All guide prices.
Planning, building control and safety law in England
In England, Approved Document L (2021) sets a limiting U-value of 1.3 W/m²K for vehicle access and similar large doors in new and replacement work. That shapes door specification for sites in Tyne and Wear, so we confirm the requirement for your project and check what applies at survey before recommending a door.
Questions
How long does installation take at a site in Tyne and Wear?
It depends on the equipment, the number of bays, the condition of the dock and whether any building or electrical work is needed. We agree a programme with you after the survey, setting out which bays are out of use and when. Larger jobs are usually phased so that part of the dock stays open, and out-of-hours working can be arranged.
Do you cover Tyne and Wear for high-speed dock doors?
Yes. We take on high-speed dock doors for businesses in Tyne and Wear and across Tyne and Wear. We survey the site, provide a fixed written quote and manage the installation, with specialist installation engineers working under our management. Visits are arranged in advance at a time that suits your operation, and the same single contact stays with the job through to handover.
What happens if a forklift hits a high-speed door?
On a door with a self-repairing curtain or breakaway bottom bar, the curtain is pushed out of its guides and re-engages on the next cycle, usually with no repair needed. Repeated hard impacts still wear the curtain and guides, so knocks should be logged and checked at the next service visit.
How often should a high-speed door be serviced?
Service frequency should follow how hard the door works, and a busy high-speed door usually needs more visits than a quiet sectional door. We agree a schedule based on cycles per day, the manufacturer's recommendations and any history of impacts. Every visit should include a check of the light curtain, photocells and bottom edge.
Other services in Tyne and Wear
Full guide to high-speed dock doors · All loading bay services in Tyne and Wear