- Location
- Shoreham-by-Sea, West Sussex
- Main postcode district
- BN43
- Nearby (straight line)
- Lancing (2 miles), Portslade (3 miles) and Worthing (5 miles)
- Visit pricing
- Agreed in writing before we attend
Dock shelter and seal repair covers restoring the weather seal around a docked trailer. Typical work includes replacing torn side and head curtains, worn foam seal pads and their covers, top pads and guide strips, repairing or replacing airbags and blowers on inflatable shelters, and straightening or replacing bent shelter frames, so the bay closes the gap between building and trailer again.
Is this right for your site in Shoreham-by-Sea?
Curtains tearing at the corners at docks in Shoreham-by-Sea can be a sign that taller or wider trailers are arriving than the shelter was sized for. Inflatable shelters at food sites in Shoreham-by-Sea depend on blowers and airbags working properly, and a slow-inflating shelter is worth checking before it fails.
Chilled distribution sites around Shoreham-by-Sea tend to notice failing seals quickly, as gaps around the trailer cause condensation and ice on the dock floor.
When something stops working at a loading bay in Shoreham-by-Sea, contact us with a description and, ideally, photos. We will confirm the cost of the visit in writing before booking anyone. If the engineer finds the problem goes further than expected, you receive a quote for the additional work and decide whether to proceed. Every visit is followed by a written report you can keep with your maintenance records.
Why is my dock shelter or seal letting in draughts?
A dock shelter or seal lets in draughts when the material that should press against the trailer is torn, worn, too short or no longer in the right place. Daylight around a docked trailer is the clearest sign.
- Torn or shrunk curtains: side curtains no longer overlap the trailer sides.
- Short head curtain: taller trailers than the shelter was sized for leave a gap across the top.
- Flattened seal pads: foam that has lost its spring no longer closes the gap.
- Worn pad covers: exposed foam soaks up water and breaks down faster.
- Bent frame: a retractable shelter frame that no longer returns square.
- Airbag or blower fault: inflatable shelters that inflate slowly or lose pressure.
- Trailer position: off-centre parking or worn bumpers that let trailers crush one side.
On chilled docks, gaps also show up as condensation, ice on the dock floor or frost around the door.
What happens on site during a shelter or seal repair?
During a shelter or seal repair the bay is closed to trailers while the engineer works from the yard, often using access equipment for the head curtain and top pad. Neighbouring bays can usually keep working, although access equipment may need space in front of them.
- Measure: where parts are made to measure, the shelter or seal is measured first and the parts ordered.
- Close the bay: no trailer on the dock and the yard area coned off.
- Isolate: on inflatable shelters, the blower supply is isolated and locked off.
- Replace parts: old curtains, pads or airbags are removed and new ones fitted, with frames straightened or replaced as agreed.
- Check the seal: overlap and compression are checked, with a trailer docked if one is available.
It helps if you can provide photos with a trailer docked, yard space for access equipment, a contact who can arrange electrical isolation and an agreed time when the bay can be released.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What else does the engineer check at the bay?
- Shelter curtains, frames and side pads for tears
- Vehicle restraint engagement and its signal sequence
- Traffic light function and interlock operation
- Track alignment, rollers and wall fixings
- Inflatable shelter fans, airbags and control function
- Wiring, isolators and motor performance under load
Options to discuss
Top pad and guide strip replacement
Renewing head pads, top seals and high-visibility guide strips that close the gap above the trailer and help drivers line up on the bay.
Airbag and blower repairs
Repairing or replacing torn airbags, failed blower motors and controls on inflatable shelters so the bags inflate fully and seal around the trailer again.
Regulations and approvals in England
Sites in Shoreham-by-Sea fall under the rules for England. Structural changes such as forming a new opening or a dock leveller pit may need Building Regulations approval, and external structures such as loading houses, canopies or new dock approaches can need planning permission from the local planning authority. We check what applies before any work starts and build any approvals into the plan.
Questions about dock shelter and seal repairs in Shoreham-by-Sea
Do you provide a written report after each visit?
Yes. After every repair or service visit to a site in Shoreham-by-Sea, you receive a written report setting out what was checked, what was found, what work was carried out and anything that still needs attention, with a quote for further work where needed. The report is useful for your maintenance records and for discussions with your insurer or inspector.
What information helps before a repair visit?
Photos or a short video of the fault are the most useful thing you can send, along with the make and model from the data plate, a description of what happens when the equipment is operated and any error codes. For a site in Shoreham-by-Sea, also tell us about access, parking and site rules. With that, we can price the visit and bring the likely parts.
Can you take over our existing loading bay maintenance arrangement?
Yes. Send us a list of the equipment at your Shoreham-by-Sea site, with makes, models and approximate ages if known, plus recent service or inspection reports. We will propose a planned maintenance schedule and price it per item per visit. The first visit records the condition of everything, so you have a clear starting point for future servicing.
How is the price for a shelter or seal repair agreed?
You describe the damage and send photos, and we agree the visit price in writing before anyone attends. For made-to-measure parts that may include a measuring visit. Any extra work found on site is quoted and only carried out once you approve it.
Can you replace just the curtains on a dock shelter?
Yes. If the frame is still sound, the side and head curtains can be replaced on their own, which is the most common shelter repair. Curtains are usually made to measure, so the shelter is measured first and the new curtains fitted on a second visit, with both visits priced in advance.
Dock shelter and seal repairs near Shoreham-by-Sea
Other towns within reach of Shoreham-by-Sea on our coverage list include Lancing (2 miles), Portslade (3 miles) and Worthing (5 miles), all covered on the same terms.
Other loading bay services in Shoreham-by-Sea
Full guide to dock shelter and seal repairs · Everything we do in Shoreham-by-Sea
Whether it is a new bay or a fault on an existing one, call us or request a quote for your site in Shoreham-by-Sea.