- Location
- Corby, Northamptonshire
- Main postcode district
- NN17
- Nearby (straight line)
- Uppingham (6 miles), Kettering (7 miles) and Market Harborough (10 miles)
- Visit pricing
- Agreed in writing before we attend
Dock shelter and seal repair covers restoring the weather seal around a docked trailer. Typical work includes replacing torn side and head curtains, worn foam seal pads and their covers, top pads and guide strips, repairing or replacing airbags and blowers on inflatable shelters, and straightening or replacing bent shelter frames, so the bay closes the gap between building and trailer again.
What should sites in Corby consider?
If tenants change at a unit in Corby, checking the shelters and seals is sensible, because a new fleet may not suit the old curtain sizes. Older retractable shelters on estates around Corby can often be refurbished with new curtains and pads rather than replaced, provided the frame is still sound.
Multi-bay sites near Corby often find several shelters in similar condition, so measuring and replacing curtains across the dock in one programme can reduce costs.
For dock shelter and seal repairs at sites in Corby, you will always know the cost before anyone sets off. The visit is chargeable and its price is agreed in writing. Clear photos of the problem help the engineer arrive prepared. Where the visit reveals more work, we stop, explain and quote before going further, and a written report follows every attendance so you have a record of the condition of each item.
Worth knowing if you run a loading operation from Corby or nearby: Northamptonshire's distribution cluster runs along the A43 and A14 corridors. When specifying a bay, the trailer mix and dock height are what count.
Why is my dock shelter or seal letting in draughts?
A dock shelter or seal lets in draughts when the material that should press against the trailer is torn, worn, too short or no longer in the right place. Daylight around a docked trailer is the clearest sign.
- Torn or shrunk curtains: side curtains no longer overlap the trailer sides.
- Short head curtain: taller trailers than the shelter was sized for leave a gap across the top.
- Flattened seal pads: foam that has lost its spring no longer closes the gap.
- Worn pad covers: exposed foam soaks up water and breaks down faster.
- Bent frame: a retractable shelter frame that no longer returns square.
- Airbag or blower fault: inflatable shelters that inflate slowly or lose pressure.
- Trailer position: off-centre parking or worn bumpers that let trailers crush one side.
On chilled docks, gaps also show up as condensation, ice on the dock floor or frost around the door.
Should I repair my dock shelter or change to a different type?
Repair is usually right when the shelter or seal still suits your trailers and the damage is wear and tear. Changing type is worth considering when the same damage keeps recurring because the equipment no longer suits the vehicles arriving.
- Repair: curtains torn by normal use, worn pad covers, a failed blower or a single bent frame arm.
- Resize: head curtains or pads that are too short for taller trailers now in your fleet.
- Seal to shelter: foam seals suit consistent trailer sizes; a mixed fleet or curtain-siders may need a shelter instead.
- Retractable to inflatable: chilled or frozen docks that need a tighter seal around varied trailers.
- Frame type: shelters repeatedly bent by trailers may suit a retractable frame that gives on impact.
Any change of type is quoted separately from the repair. Our guide to dock shelters vs dock seals explains how each type works and which trailers it suits.
The visit price is agreed before anyone attends. Parts and any extra work are quoted before they are fitted.
What else does the engineer check at the bay?
- Leveller toe guards and side skirting, where fitted
- Safety edges, photocells and light curtains
- Vehicle restraint engagement and its signal sequence
- Manual override and emergency operation on powered doors
- Wiring, isolators and motor performance under load
- Door springs, cables and drums for wear or damage
Options to discuss
Top pad and guide strip replacement
Renewing head pads, top seals and high-visibility guide strips that close the gap above the trailer and help drivers line up on the bay.
Curtain replacement
New side and head curtains for retractable shelters, made to measure in hard-wearing coated fabric, with slits and overlaps set to suit the trailers you receive.
Regulations and approvals in England
Powered doors and dock equipment installed in England may carry the UKCA or the CE mark, and doors are covered by the product standard BS EN 13241. We hand over the relevant documentation for each item fitted in Corby. Planning and Building Regulations questions are never assumed either way: we check what applies before any work starts, so you know before work is booked.
Questions about dock shelter and seal repairs in Corby
How is a repair or service visit in Corby priced?
Repair and service visits are chargeable, and the price is agreed in writing before anyone attends. For dock shelter and seal repairs, the guide budget is £380 to £1,800 per repair, excluding VAT. The exact figure depends on the fault, parts, access and timing. If the engineer finds further work on the day, it is quoted for your approval before it is carried out.
Can you repair all makes of loading bay equipment?
We work on common makes and types of doors, dock levellers, shelters, seals and restraints. Parts availability varies, particularly for older or discontinued equipment, so it helps to send the make, model and photos of any data plates from your site in Corby. If original parts are not available, we tell you and price the alternatives, including replacement where that makes more sense.
What is the difference between servicing and a statutory inspection?
Servicing keeps equipment working: cleaning, adjusting, lubricating and replacing worn parts. A statutory inspection or thorough examination is a separate check by a competent person, often arranged through your engineering insurer. Dock levellers are commonly inspected under PUWER at 12-month intervals, and lift tables may need LOLER thorough examination, depending on the equipment and how it is used. Your insurer or competent person will confirm what applies.
Can worn dock seal covers be replaced without new foam?
Often, yes. If the foam inside a seal pad still springs back, a new cover can be fitted over it. If the foam has stayed compressed or soaked up water, the pad is usually replaced complete. Photos of the pads, front and side, help us judge which applies.
Why do shelter curtains keep tearing?
Shelter curtains usually keep tearing because trailers arrive off-centre, the curtains are too short or tight for the trailers now in use, or worn bumpers let trailers reverse too far in. Fixing the cause, for example with wheel guides or resized curtains, stops repeat damage.
Dock shelter and seal repairs near Corby
The same survey, quote and repair service is available in towns around Corby, such as Uppingham (6 miles), Kettering (7 miles) and Market Harborough (10 miles).
Other loading bay services in Corby
Full guide to dock shelter and seal repairs · Everything we do in Corby
Use the quote tool to tell us about the doors, levellers or shelters at your Corby site, and we will be in touch to arrange the next step.