- Location
- Stornoway, Orkney, Shetland and the Western Isles
- Main postcode district
- HS1
- Nearby (straight line)
- Remote location, covered by arrangement
- Survey and quote
- Free, with a fixed written quote
A dock seal is a set of fabric-covered foam pads fixed to the building around a loading bay door, usually a head pad and two side pads. When a trailer reverses in, its rear end presses into the foam, which compresses to close the gaps around the trailer body. Seals give a very tight fit but work best when the trailers using the bay are a consistent size.
Why do sites in Stornoway choose this?
Own-fleet distribution sites in Stornoway, where the same trailers arrive day after day, are well suited to foam dock seals and the tight fit they give. Heated packing halls next to a dock in Stornoway lose less warmth during loading when the gap around each trailer is closed by compressed foam.
Hygiene-sensitive sites in Stornoway, such as food processors, can use dock seals to reduce the gaps through which dust and pests might enter during loading.
We keep the process simple for sites in Stornoway. A free survey tells us what the dock needs; a fixed written quote tells you what it will cost and what is included. We then organise the installation, with specialist engineers under our management and a programme agreed around your shifts. Night and weekend work is available by arrangement. Before we leave, the new equipment is tested, demonstrated and handed over with its documentation.
What do workplace transport rules mean for a sealed dock?
A sealed dock still needs safeguards against a trailer leaving early, and the seal, bumpers and other dock equipment must be kept in safe working order. In Great Britain the regulator is HSE; in Northern Ireland it is HSENI.
- Drive-away: HSE workplace transport guidance (HSG136) and the HSE loading factsheet call for safeguards against drivers driving away too early, including traffic lights, vehicle or trailer restraints, or the person in charge keeping keys or paperwork until it is safe.
- Trailer creep: because the trailer is pressed into compressed foam, it can ease forward during forklift loading. Restraints and well-set bumpers help keep it in position.
- Equipment duties: a dock seal forms part of the loading bay's work equipment, so the general duty under PUWER 1998 in Great Britain, or PUWER (Northern Ireland) 1999, to keep equipment suitable and maintained applies.
Torn covers and crushed pads can hide damage to the fixings and wall behind, so seals belong in planned inspections of the dock.
How can dock seal pads be made to last longer?
Dock seal pads last longer when trailers arrive straight and stop at the right point, because most wear comes from trailers rubbing against the covers or pressing too far into the foam. Covers usually wear first, and the foam inside can outlast them.
- Replaceable wear pleats: sacrificial strips on the pad faces take the abrasion and can be swapped cheaply.
- Wheel guides and dock lights: help drivers reverse squarely into the centre of the bay.
- Bumper maintenance: keeps compression within design limits.
- Tapered side pads: guide trailers in and reduce rubbing on the pad edges.
- Driver briefings: regular hauliers who know the bay damage it less.
When covers split, replacing them promptly stops rain soaking into the foam, which makes it heavy, slow to recover and prone to freezing in winter.
The same published guide range applies across Scotland; access, out-of-hours working and site conditions are confirmed at the free survey.
What do we check at the survey?
- How often each door cycles during a typical shift
- Temperature requirements for chilled, frozen or ambient goods
- Condition of any existing leveller pit, kerb angles and pit drainage
- Yard gradient and the slope of the approach to the dock
- Whether planning, building control or a building warrant may be needed
- Drainage on recessed or sloping dock approaches
Options to discuss
Fixed head pad seal
A head pad and two side pads of set depth, the simplest and tightest arrangement where every trailer using the bay is the same height.
Seal with curtain head
Foam side pads combined with a flexible top curtain that adjusts to trailers of different heights, a halfway point between a seal and a shelter.
Planning, building control and safety law in Scotland
Energy standards for buildings in Scotland are set out in Section 6 of the Building Standards Technical Handbook. For new or replacement loading bay doors in Stornoway, we confirm the figure that applies to your project and check what applies at survey, rather than relying on rules written for elsewhere in the UK.
We cover Stornoway by arrangement. The survey and written quote stay free: for remote and island sites we often start from your photos, drawings and a video call, then confirm measurements on site. Travel and any accommodation needed for the installation are shown as separate lines in the fixed quote.
Questions about dock seals in Stornoway
Can you work outside our normal operating hours in Stornoway?
Yes, by arrangement. Evening, night and weekend working can be planned so the installation causes as little disruption as possible to your loading schedule. Out-of-hours work can affect the price, so mention it at the survey and we will include it in the written quote. The agreed times are confirmed in the programme before the job starts.
What warranty comes with new loading bay equipment?
New equipment comes with the manufacturer's warranty, which varies by product. Our workmanship terms are set out in writing in the quote for your Stornoway site, so you can see what is covered before you commit. Check the warranty terms for any servicing conditions, and we can quote for planned maintenance once the installation is complete.
Will you deal with building control and planning for a project in Stornoway?
We check at survey whether the work is likely to need approval. Forming a new opening or dock pit may need Building Regulations approval, a building warrant or building control approval, depending on the nation, and external structures such as loading houses can need planning permission. Where approval is needed, we explain what is involved, work with your designer or agent, and build it into the programme.
Can just the covers be replaced?
Yes, if the foam is still resilient and dry, new covers can often be fitted over the existing foam, which usually costs less than new pads. Waterlogged or permanently crushed foam should be replaced. Cover replacement is handled as a repair, with the visit price agreed beforehand.
Are dock seals suitable for cold stores?
Yes, for cold stores with consistent trailers a dock seal gives a tight fit at a lower cost than an inflatable shelter. The pads must be kept in good condition, because water in the foam can freeze and stiffen it. Mixed fleets at cold stores are often better served by inflatable shelters.
Dock seals near Stornoway
Other loading bay services in Stornoway
Full guide to dock seals · Everything we do in Stornoway
Send a few photos of the dock and a short description of the problem, and we will come back to you about your Stornoway site.